주요 콘텐츠로 건너뛰기

필요한 것

  1. Removing Bottom of iMac G4 15" 700 MHz EMC 1873, Outer Base Plate: 1 단계, 이미지 1/2 Removing Bottom of iMac G4 15" 700 MHz EMC 1873, Outer Base Plate: 1 단계, 이미지 2/2
    • Place the computer monitor face down on a safe, harmless surface.

    • Using a Phillips #00 screw driver, remove the four 6.86 mm screws from the metal plate.

  2. Removing Bottom of iMac G4 15" 700 MHz EMC 1873: 2 단계, 이미지 1/1
    • Remove the metal plate from bottom of the iMac G4.

    • The four screws do not completely separate from the metal plate.

  3. Removing Bottom of iMac G4 15" 700 MHz EMC 1873, RAM DIMM: 3 단계, 이미지 1/2 Removing Bottom of iMac G4 15" 700 MHz EMC 1873, RAM DIMM: 3 단계, 이미지 2/2
    • Release the tabs on each side of the module by simultaneously pushing each tab away from the RAM.

    • These tabs lock the module in place and releasing them will cause the module to "pop" up.

    • Remove the RAM module from the iMac.

  4. Removing Bottom of iMac G4 15" 700 MHz EMC 1873, AirPort Card: 4 단계, 이미지 1/1
    • Use a spudger to lift and remove the AirPort's antenna connector.

    • This step is only applicable to iMacs that came with an AirPort card installed.

  5. Removing Bottom of iMac G4 15" 700 MHz EMC 1873, Removing the Lower Case: 5 단계, 이미지 1/1
    • Remove the four 28.07mm Torx #15 screws from the lower case.

  6. Removing Bottom of iMac G4 15" 700 MHz EMC 1873: 6 단계, 이미지 1/2 Removing Bottom of iMac G4 15" 700 MHz EMC 1873: 6 단계, 이미지 2/2
    • Open the base by carefully pulling straight off, do not rotate the cover.

    • Open slowly to ensure that no cables are damaged or disconnected.

  7. Removing Bottom of iMac G4 15" 700 MHz EMC 1873: 7 단계, 이미지 1/1
    • Squeeze the small black tab and wiggle gently to remove the colored power cable.

    • Do not pull directly on the colored wires.

    • Do not remove black grounding wire.

  8. Removing Bottom of iMac G4 15" 700 MHz EMC 1873: 8 단계, 이미지 1/1
    • Grab both sides of the blue connector and firmly pull to remove it from the mother board.

    • Do not pull directly on the ribbon cable.

결론

To reassemble your device, follow these instructions in reverse order.

다른 8명이 해당 안내서를 완성하였습니다.

Elliot Freerks

회원 가입일: 2011년 10월 04일

837 평판

안내서 3개 작성하였습니다

Cal Poly, Team 5-32, Amido Fall 2011 Cal Poly, Team 5-32, Amido Fall 2011 회원

CPSU-AMIDO-F11S5G32

4 회원들

안내서 8개 작성하였습니다

One Comment

Do I need to apply thermal paste? Or it is not necessary?

willynanita - 답글

댓글 쓰기

조회 통계:

24 시간 전: 2

7일 전: 4

30일 전: 27

전체 시간: 5,916