메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Removing HP Compaq dx2000MT Power Supply

작성자 Logan Pace (또 다른 기여자 2명)
  • 댓글 1
  • 즐겨찾기 13
  • 완료: 7

난이도

보통

단계

8

소요 시간

시간 제안??

섹션

2

플래그

1

Markup Mishap

마크업 사고

해당 안내서는 더 나은 마크업이 필요합니다. 일부 마크업 주석의 편집 또는 작성을 도와주십시오!

소개

This guide will show you how to remove the power supply on your HP Compaq dx2000MT.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Turn off your computer and remove the power cable by pulling it straight out of its socket.

    • Turn off your computer and remove the power cable by pulling it straight out of its socket.

    편집

  2. Remove the two Phillips #2 screws that secure the case door to the device. Remove the two Phillips #2 screws that secure the case door to the device.

    • Remove the two Phillips #2 screws that secure the case door to the device.

    편집

  3. Remove the side case door by pushing towards the rear of the device with your hand. This may take considerable force so keep pushing! Once you slide the door back, remove it by pulling it outwards from the device.

    • Remove the side case door by pushing towards the rear of the device with your hand.

    • This may take considerable force so keep pushing!

    • Once you slide the door back, remove it by pulling it outwards from the device.

    편집

  4. 안드로이드 수리 키트

    A new screen or battery is one kit away.

    지금 장보기

    안드로이드 수리 키트

    A new screen or battery is one kit away.

    지금 장보기

  5. Remove the side case door by pushing towards the rear of the device with your hand. Once again, this may take considerable force. Once you slide the door back, remove it by pulling it outwards from the device.

    • Remove the side case door by pushing towards the rear of the device with your hand.

    • Once again, this may take considerable force.

    • Once you slide the door back, remove it by pulling it outwards from the device.

    편집

  6. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

    • Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

    편집

  7. Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

    • Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

    편집

  8. Remove the 4 Torx T15 screws from the rear of the power supply Remove the 4 Torx T15 screws from the rear of the power supply Remove the 4 Torx T15 screws from the rear of the power supply

    • Remove the 4 Torx T15 screws from the rear of the power supply

    편집

  9. Slide the power supply towards the front of the device Keep your hand underneath it! You don't want to drop it!

    • Slide the power supply towards the front of the device

    • Keep your hand underneath it! You don't want to drop it!

    • Then pull the power supply down and remove it from the case.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 7명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 2명과 함께

Logan Pace

회원 가입일: 2011년 10월 12일

2,020 평판

안내서 9개 작성하였습니다

배지: 14

배지 +11개 더

팀

Cal Poly, Team 17-16, Regan Fall 2011 Cal Poly, Team 17-16, Regan Fall 2011 회원

CPSU-REGAN-F11S17G16

4 회원들

안내서 17개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 2

지난 30일: 5

전체 시간: 2,519