기기를 수리하세요 커뮤니티 상점

Resetting PlayStation 3 Drive Mechanism

보관된 가이드
해당 안내서는 단지 역사적인 목적으로 보관됩니다. 최신 버전 안내서를 사용하여 수리 하십시오.

필요한 것

  1. Resetting PlayStation 3 Drive Mechanism, Resetting PlayStation 3 Drive Mechanism: 1 단계, 이미지 1/1

    • Remove Rubber Foot

    편집

  2. Resetting PlayStation 3 Drive Mechanism: 2 단계, 이미지 1/1

    • Remove Screw with a TORX Security T10 Bit (or you can use a small flat head screwdriver)

    편집

  3. Resetting PlayStation 3 Drive Mechanism: 3 단계, 이미지 1/1

    • Carefully slide the top plate and lift to remove

    편집

  4. Resetting PlayStation 3 Drive Mechanism: 4 단계, 이미지 1/1

    • Remove the main screws (philips head)

    편집

  6. Resetting PlayStation 3 Drive Mechanism: 5 단계, 이미지 1/1

    • Lift The Top Casing Towards the front of the PS3 carefully

    편집

  7. Resetting PlayStation 3 Drive Mechanism: 6 단계, 이미지 1/1

    • Carefully Remove Power cable from the motherboard

    편집

  8. Resetting PlayStation 3 Drive Mechanism: 7 단계, 이미지 1/1

    • Lift the Disk drive to the right and remove the largest ribbon cable by lifting the black catch and remove the drive from the PS3

    편집

  9. Resetting PlayStation 3 Drive Mechanism: 8 단계, 이미지 1/1

    • Remove Screws 11, 12 and 13 only

    편집

  10. Resetting PlayStation 3 Drive Mechanism: 9 단계, 이미지 1/1

    • Remove screws 14 and 15 and the silver springboard, slightly bend top metal away from disk entry area,and pull back to remove the metal jacket.

    편집

  11. Resetting PlayStation 3 Drive Mechanism: 10 단계, 이미지 1/1

    • Remove white center hub piece (D) and screws 16 - 20 then fold the top section to the left being careful not to damage the cable to the bottom left. The cable is very delicate and easily damaged.

    편집

  12. Resetting PlayStation 3 Drive Mechanism: 11 단계, 이미지 1/1

    • Remove the screw circled in red and lift up the black assembly to reveal the mechanism beneath. Set it aside right-side up and be careful not to shake any parts loose.

    편집

  13. Resetting PlayStation 3 Drive Mechanism: 12 단계, 이미지 1/1

    • Remove two screws in blue and lift the motor up and to right to disengage the cogs but be careful not to stress the attached wires.

    • Move the disc handling element on the left side up so that its teeth are clear of the black cog.

    • Reset insertion trap lock mechanism and make sure the white tab on right is lowered (nudge it left to make it drop).

    • Replace the motor and reverse this guide to reassemble.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 15명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

David Harris

회원 가입일: 09/15/12

816 평판

안내서 1개 작성함

배지: 7

배지 +4개 더

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 2

30일 전: 4

전체 시간: 15,929