기기를 수리하세요 커뮤니티 상점

Ridgid Angle Grinder R10202 Motor Housing Replacement

소개

Inspection of the motor housing is an important step in determining damage to the inner workings of the grinder. Visual inspection or repair of the gear housing, or "V" motor assembly, will require this guide.

필요한 것

  1. Ridgid Angle Grinder R10202 Motor Housing Replacement, Carbon Brush: 1 단계, 이미지 1/2 Ridgid Angle Grinder R10202 Motor Housing Replacement, Carbon Brush: 1 단계, 이미지 2/2

    • Use a flathead screwdriver to unscrew the brush holder cap.

    편집

  2. Ridgid Angle Grinder R10202 Motor Housing Replacement: 2 단계, 이미지 1/2 Ridgid Angle Grinder R10202 Motor Housing Replacement: 2 단계, 이미지 2/2

    • Using your fingers, gently lift the carbon brush up and out of its housing.

    • Repeat these steps to remove the other carbon brush on the opposing side.

    편집

  3. Ridgid Angle Grinder R10202 Motor Housing Replacement, Motor Housing: 3 단계, 이미지 1/1

    • Unscrew the side handle assembly from the gear housing assembly by hand.

    편집

  5. Ridgid Angle Grinder R10202 Motor Housing Replacement: 4 단계, 이미지 1/1

    • Unscrew the clamp nut and the backing flange from the output shaft assembly.

    • You can do this by hand or use a spanner wrench which should be provided in the manufacturers box.

    편집

  6. Ridgid Angle Grinder R10202 Motor Housing Replacement: 5 단계, 이미지 1/2 Ridgid Angle Grinder R10202 Motor Housing Replacement: 5 단계, 이미지 2/2

    • Push in the guard lever and twist the guard until it aligns with the slots on the output shaft assembly.

    • There are two arrows that should align before you attempt to pull the pieces apart.

    편집

  7. Ridgid Angle Grinder R10202 Motor Housing Replacement: 6 단계, 이미지 1/1

    • Lift the guard away from the output shaft assembly.

    편집

  8. Ridgid Angle Grinder R10202 Motor Housing Replacement: 7 단계, 이미지 1/2 Ridgid Angle Grinder R10202 Motor Housing Replacement: 7 단계, 이미지 2/2

    • Using a T25 Torx screwdriver, unscrew the four M5 X 28mm Torx screws.

    편집

  9. Ridgid Angle Grinder R10202 Motor Housing Replacement: 8 단계, 이미지 1/3 Ridgid Angle Grinder R10202 Motor Housing Replacement: 8 단계, 이미지 2/3 Ridgid Angle Grinder R10202 Motor Housing Replacement: 8 단계, 이미지 3/3

    • Grab the handle assembly and the gear housing assembly and gently pull apart.

    • Slowly pull the gear housing assembly out being careful not to damage the motor against the inside of the motor housing.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 4명과 함께

Parker Massie

회원 가입일: 01/10/19

607 평판

안내서 4개 작성하였습니다

배지: 8

배지 +5개 더

팀

Oregon Institute of Technology, Team S1-G2, Lancaster Winter 2019 Oregon Institute of Technology, Team S1-G2, Lancaster Winter 2019 회원

OIT-LANCASTER-W19S1G2

4 회원들

안내서 6개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 7

전체 시간: 797