기기를 수리하세요 커뮤니티 상점

Ridgid GEN5X R8642 Blade Clamp Assembly Replacement

소개

This guide is to help users replace the blade clamp assembly for the Ridgid GEN5X R8642 saw. For this guide you will need: a spudger, a T20 Torx Screwdriver, a Phillips screwdriver size J1, replacement gear assembly for Ridgid GEN5X R8642, and a good attitude.

필요한 것

  1. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement, Blade Clamp Assembly: 1 단계, 이미지 1/1

    • Remove the plastic tab holding the handle cover in place by prying upward with the spudger until the tab pops off.

    편집

  2. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 2 단계, 이미지 1/1

    • Remove the handle cover by pulling it towards the front of the saw.

    • The grip can sometimes become stuck and may require a decent amount of force to remove.

    편집

  3. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 3 단계, 이미지 1/2 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 3 단계, 이미지 2/2

    • Use a T20 Torx screwdriver to remove the nine M4 X 16mm screws from the plastic housing.

    편집

  4. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 4 단계, 이미지 1/1

    • Use a JIS #1 screwdriver to remove the two M4 x 25mm screws on both sides of the metal housing.

    편집

  5. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 5 단계, 이미지 1/1

    • Remove one half of the plastic housing using a spudger so that the internal system is exposed.

    편집

  7. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 6 단계, 이미지 1/2 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 6 단계, 이미지 2/2

    • Remove the one 16mm T20 screw that holds the grip support onto the saw.

    편집

  8. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 7 단계, 이미지 1/3 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 7 단계, 이미지 2/3 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 7 단계, 이미지 3/3

    • Remove the five T20 Torx screws from the gear assembly cover and pull the cover off.

    편집

  9. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 8 단계, 이미지 1/2 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 8 단계, 이미지 2/2

    • Carefully remove the motor making sure not to harm any of the wires that are attached. Place motor gently out of the way.

    편집

  10. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 9 단계, 이미지 1/3 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 9 단계, 이미지 2/3 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 9 단계, 이미지 3/3

    • Remove the orbital switch by pulling straight up on it.

    • Be careful to not lose the spring and pin that is inside of the switch.

    편집

  11. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 10 단계, 이미지 1/3 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 10 단계, 이미지 2/3 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 10 단계, 이미지 3/3

    • Remove the gear assembly by pulling it straight up.

    편집

  12. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 11 단계, 이미지 1/3 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 11 단계, 이미지 2/3 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 11 단계, 이미지 3/3

    • Pull the pin holding the metal guide housing in place.

    • Slide the metal guide housing back off the gear assembly.

    편집

  13. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 12 단계, 이미지 1/2 Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 12 단계, 이미지 2/2

    • Remove the guide bushing by pulling up on it.

    • Then slide the pin out that holds the gear assembly and blade clamp assembly.

    편집

  14. Ridgid GEN5X R8642 Blade Clamp Assembly Replacement: 13 단계, 이미지 1/1

    • Slide the blade clamp assembly off the gear assembly.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Grant White

회원 가입일: 02/12/19

453 평판

안내서 2개 작성하였습니다

배지: 7

배지 +4개 더

팀

Western Carolina University, Team S1-G3, Virtue Spring 2019 Western Carolina University, Team S1-G3, Virtue Spring 2019 회원

WCU-VIRTUE-S19S1G3

4 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 14

30일 전: 40

전체 시간: 1,667