기기를 수리하세요

수리할 권리

상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

Rival 16131 Toaster Power Wire Repair

작성자 Grant Haug (또 다른 기여자 3명)
  • 댓글 0
  • 즐겨찾기 0

난이도

어려움

단계

7

소요 시간

20 분

섹션

2

플래그

4

Needs More Images

더 많은 이미지가 필요함

몇몇 추가 이미지는 해당 안내서의 절차를 아주 명백하게 만들 것입니다.

Action Shots

액션 샷

액션 영웅이 되십시오! 해당 안내서는 특정 액션을 더 잘 보여주기 위한 사진들이 필요합니다.

Markup Mishap

마크업 사고

해당 안내서는 더 나은 마크업이 필요합니다. 일부 마크업 주석의 편집 또는 작성을 도와주십시오!

Better Introduction

더 나은 소개글

소개글을 완성 또는 수정하여 해당 안내서를 개선하여 주십시오.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Make sure the toaster is unplugged before dissembling. Turn the toaster over and remove the rubber bumper feet.

    • Make sure the toaster is unplugged before dissembling.

    • Turn the toaster over and remove the rubber bumper feet.

    편집

  2. Use a Phillips head screwdriver to remove all four 12 mm screws that are attached to the toaster shell. Use a Phillips head screwdriver to remove all four 12 mm screws that are attached to the toaster shell.

    • Use a Phillips head screwdriver to remove all four 12 mm screws that are attached to the toaster shell.

    편집

  3. With the dial facing you, push the toaster base up and away until the base is just over the lip of the shell. This will disconnect the browning dial from the rest of the toaster. When reassembling the toaster, make sure that the back of the dial lines up with the slot, both in position and orientation (the dial and slot are not perfect circles - they have a notch). The only object holding the shell onto the toaster now is the grey part of the lever.

    • With the dial facing you, push the toaster base up and away until the base is just over the lip of the shell. This will disconnect the browning dial from the rest of the toaster.

    • When reassembling the toaster, make sure that the back of the dial lines up with the slot, both in position and orientation (the dial and slot are not perfect circles - they have a notch).

    • The only object holding the shell onto the toaster now is the grey part of the lever.

    편집

  5. Reach into the shell and grab the back white part of the lever.

    • Reach into the shell and grab the back white part of the lever.

    • Hold the grey lever with both your index finger and middle finger. Next, pull it.

    • Pulling too hard will break the mechanism that holds the grey handle onto the white lever.

    • Next, remove the shell.

    편집

  6. The power wire connects to the toaster in the area highlighted. To free the wire, unscrew the two .5 inch screws, and remove the white brace.

    • The power wire connects to the toaster in the area highlighted.

    • To free the wire, unscrew the two .5 inch screws, and remove the white brace.

    편집

  7. To solder the the wire, the circuit board has to be released.

    • To solder the the wire, the circuit board has to be released.

    • To do this, unscrew the .5 inch screw located in the middle of the board.

    • Slowly lift the board up off the toaster, making sure that the red pegs that hold the board in place do not break.

    편집

  8. To reattach the wire, follow this solder guide.

    • To reattach the wire, follow this solder guide.

    • Solder Guide

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 3명과 함께

Grant Haug

회원 가입일: 2012년 09월 26일

139 평판

안내서 4개 작성하였습니다

배지: 10

배지 +7개 더

팀

Cal Poly, Team 2-8, Propen Fall 2012 Cal Poly, Team 2-8, Propen Fall 2012 회원

CPSU-PROPEN-F12S2G8

5 회원들

안내서 6개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 13

전체 시간: 1,545