기기를 수리하세요 커뮤니티 상점

Rival CM4015 Heating Element Replacement

소개

The Rival single cup coffee maker has a heating element that is prone to breaking. If the device is left on for too long, the heating element can over heat and stop working.

필요한 것

  1. Rival CM4015 Heating Element Replacement, Base Plate: 1 단계, 이미지 1/2 Rival CM4015 Heating Element Replacement, Base Plate: 1 단계, 이미지 2/2

    • Remove the three 16 mm tri-point screws from the base plate.

    편집

  2. Rival CM4015 Heating Element Replacement: 2 단계, 이미지 1/2 Rival CM4015 Heating Element Replacement: 2 단계, 이미지 2/2

    • Remove the base plate by pressing the plastic body away from the metal plate with your thumbs.

    편집

  3. Rival CM4015 Heating Element Replacement, Power Button: 3 단계, 이미지 1/1

    • Remove the 8mm Phillips screw that attaches the power button to the inside of the coffee maker.

    편집

  4. Rival CM4015 Heating Element Replacement: 4 단계, 이미지 1/2 Rival CM4015 Heating Element Replacement: 4 단계, 이미지 2/2

    • Use a flat head screwdriver to pry the power button from its slot in the body of the device.

    • Make sure the tool is pressed securely under the plastic clip, in order to not break it.

    편집

  6. Rival CM4015 Heating Element Replacement: 5 단계, 이미지 1/2 Rival CM4015 Heating Element Replacement: 5 단계, 이미지 2/2

    • Clean both the button and its slot before replacing the power button.

    편집

  7. Rival CM4015 Heating Element Replacement, Heating Element: 6 단계, 이미지 1/1

    • Remove the two 8 mm Phillips screws from the plastic body.

    편집

  8. Rival CM4015 Heating Element Replacement: 7 단계, 이미지 1/2 Rival CM4015 Heating Element Replacement: 7 단계, 이미지 2/2

    • Remove the two 8 mm Phillips screws from the chassis of coffee maker.

    • Pull back the metal backing from the plastic body.

    편집

  9. Rival CM4015 Heating Element Replacement: 8 단계, 이미지 1/3 Rival CM4015 Heating Element Replacement: 8 단계, 이미지 2/3 Rival CM4015 Heating Element Replacement: 8 단계, 이미지 3/3

    • Remove the four 8 mm Phillips screws from the inner plastic body.

    • You will need a long, thin Phillips screw driver to get this deep into the device.

    편집

  10. Rival CM4015 Heating Element Replacement: 9 단계, 이미지 1/2 Rival CM4015 Heating Element Replacement: 9 단계, 이미지 2/2

    • Flip the device upside down and remove the outer plastic body from the device by pulling straight up.

    • Take your time to make sure the thin cables within the device don't tear.

    편집

  11. Rival CM4015 Heating Element Replacement: 10 단계, 이미지 1/1

    • Remove the two 8 mm Phillips screws from the metal backing.

    편집

  12. Rival CM4015 Heating Element Replacement: 11 단계, 이미지 1/1

    • Remove the 4 springs holding the water tubes by squeezing the 2 prongs together.

    • You may also use pliers for this step if the springs are too strong.

    편집

  13. Rival CM4015 Heating Element Replacement: 12 단계, 이미지 1/1

    • Bend the heating element back and forth to wiggle the water tubes loose from the plastic.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Michael Murdock

회원 가입일: 10/06/16

279 평판

안내서 2개 작성하였습니다

배지: 10

배지 +7개 더

팀

Cal Poly, Team 10-6, Livingston Fall 2016 Cal Poly, Team 10-6, Livingston Fall 2016 회원

CPSU-LIVINGSTON-F16S10G6

5 회원들

안내서 6개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 11

전체 시간: 395