소개

This guide will help you remove the safety latch for the container lid.

  1. Twist the plastic lid counterclockwise to unlock it.
    • Twist the plastic lid counterclockwise to unlock it.

    • Lift the lid to remove it from the container.

    댓글 쓰기

  2. Carefully remove the blade from the container.
    • Carefully remove the blade from the container.

    • For reassembly, the teeth on the metal shaft line up with slots on the inside of the plastic hole.

    댓글 쓰기

    • With your hand, twist the container counter-clockwise until it unlocks from the base. Remove the container by lifting it straight up.

    댓글 쓰기

    • Use your fingers to pry out the two rubber feet from the bottom cover of the base.

    • The two feet furthest from the button tower contain screws. The other two feet do not.

    댓글 쓰기

    • Use the Phillips #2 screwdriver to unscrew the two 12.7-mm screws underneath the rubber feet.

    • Use the same screwdriver to unscrew the 15.88-mm screw from the back of the chopper.

    댓글 쓰기

    • Firmly lift the bottom cover off of the base.

    댓글 쓰기

  3. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Remove the smaller white gear by lifting it up with your hand.

    댓글 쓰기

    • Use a pair of pliers or any other clamping tool to securely hold the blade-shaft that sits above the base.

    • Grab the gear with your other hand and turn CLOCKWISE. Unlike most screws, the gear is reverse-threaded to allow the blade to spin.

    • Continue turning the gear until completely removed from the blade-shaft.

    댓글 쓰기

    • Use your hand to firmly pull the blade-shaft from the base.

    댓글 쓰기

    • Using Phillips #2 screwdriver, unscrew two 12.7-mm screws in the middle of the base.

    댓글 쓰기

    • Unwind power cord from the base pegs.

    댓글 쓰기

    • Use the plastic opening tool to pry open the base from the main body.

    • These two plastic prongs are pressed fit into the base. It may take some effort to pry the base completely off.

    • Once freed, lift the base panel from the main body and set it aside.

    댓글 쓰기

    • Use a Phillips #2 screwdriver to remove the three 9.53-mm screws from inside the main body.

    • Next, turn the device upright and lift the upper casing from around the button gently.

    댓글 쓰기

    • Remove the button by simply pulling it up.

    • Don't lose the spring under the button! Without it, the blender will not function.

    댓글 쓰기

    • Use the Phillips #2 screwdriver to remove one 9.53-mm screw.

    댓글 쓰기

    • Remove the white latch by unhooking it from the spring wire and gently lifting straight up.

    댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

Roxanne

회원 가입일: 2013년 10월 17일

507 평판

안내서 4개 작성하였습니다

Cal Poly, Team 4-29, Amido Fall 2013 Cal Poly, Team 4-29, Amido Fall 2013 회원

CPSU-AMIDO-F13S4G29

4 회원들

안내서 5개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 1

지난 30일: 6

전체 시간: 1,214