메인 콘텐츠로 스킵하기

소개

The Samsung Galaxy On5 speaker is located in the back of the phone. Now getting to isn't difficult to get to, but once you're in the phone chaise everything is smooth sailing.

  1. Locate the side notch that allows you to open the back casing.
    • Locate the side notch that allows you to open the back casing.

  2. Use a plastic prying tool or your fingernail to pop the back cover off the phone. Use a plastic prying tool or your fingernail to pop the back cover off the phone. Use a plastic prying tool or your fingernail to pop the back cover off the phone.
    • Use a plastic prying tool or your fingernail to pop the back cover off the phone.

  3. Locate the battery notch to remove the battery Be careful not puncture the battery. Lithium-ion batteries are highly flammable when exposed to oxygen. Use a plastic prying tool or your fingernail to remove the battery from its housing and pull it aside.
    • Locate the battery notch to remove the battery

    • Be careful not puncture the battery. Lithium-ion batteries are highly flammable when exposed to oxygen.

    • Use a plastic prying tool or your fingernail to remove the battery from its housing and pull it aside.

  4. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now
  5. Before dissembling the phone take out the SIM card and microSD card. Use a plastic pry tool to slide both cards out.
    • Before dissembling the phone take out the SIM card and microSD card.

    • Use a plastic pry tool to slide both cards out.

    • Do not use a metal pry tool. Use of one can cause damage to the cards or the pins with the cards holder.

  6. Take the plastic Spudger tool to pry open the LCD ribbon cable cover. This part might be a little hard to open. Take your time and be careful not to push too hard, so there's no damage to the ribbon cable Once the cover is remove, place the cover aside so its not miss placed
    • Take the plastic Spudger tool to pry open the LCD ribbon cable cover.

    • This part might be a little hard to open. Take your time and be careful not to push too hard, so there's no damage to the ribbon cable

    • Once the cover is remove, place the cover aside so its not miss placed

  7. Take a plastic pry tool and work towards the top right of the LCD ribbon cable to pry the cable from the logic board. Do not use a metal pry tool. Metal pry tools can cause damage to the logic board and to the ribbon cable. This cable send signal from the logic board to the LCD screen.
    • Take a plastic pry tool and work towards the top right of the LCD ribbon cable to pry the cable from the logic board.

    • Do not use a metal pry tool. Metal pry tools can cause damage to the logic board and to the ribbon cable.

    • This cable send signal from the logic board to the LCD screen.

    • Once unplugged move the cable aside.

  8. Take a PH00 Philip head and remove all 9 screws. Once done place them aside where you won't lose them. All 9 screws are the same size.
    • Take a PH00 Philip head and remove all 9 screws. Once done place them aside where you won't lose them.

    • All 9 screws are the same size.

  9. Use iFixit plastic picks to pry away the LCD from the bask assembly. This process will take a bit due to the glue thats holding the LCD and back assembly together. Slowly move around the edge go the screen to loosen the glue up.
    • Use iFixit plastic picks to pry away the LCD from the bask assembly.

    • This process will take a bit due to the glue thats holding the LCD and back assembly together. Slowly move around the edge go the screen to loosen the glue up.

    • If you have a heat gun, you can use the heat gun heat up the glue. That will make the use of the plastic picks easy to pry the pieces apart.

  10. Once both the LCD and back assemble come apart, look at the back assembly which the speaker is located. Once located take a the plastic pry tool to remove the speaker of its housing. And replace it with a new one. Once located take a the plastic pry tool to remove the speaker of its housing. And replace it with a new one.
    • Once both the LCD and back assemble come apart, look at the back assembly which the speaker is located.

    • Once located take a the plastic pry tool to remove the speaker of its housing. And replace it with a new one.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

The Dark Night part 2

회원 가입일: 2018년 09월 19일

662 평판

안내서 5개 작성하였습니다

Gateway, Team S1-G5, Luster Fall 2018 Gateway, Team S1-G5, Luster Fall 2018 회원

GCC-LUSTER-F18S1G5

1 회원

안내서 5개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 8

지난 30일: 21

전체 시간: 142