소개

Use this guide to replace the volume buttons in your Samsung Galaxy S6.

This guide involves removing the rear glass. Removing the rear glass destroys the adhesive holding it in place. Follow this guide to reinstall the rear glass.

  1. Insert a paper clip or SIM eject tool into the hole in the SIM card slot on the power button side of the phone. Press to eject the SIM card tray.
    • Insert a paper clip or SIM eject tool into the hole in the SIM card slot on the power button side of the phone.

    • Press to eject the SIM card tray.

    • Don't press too hard or you may damage the SIM card tray.

  2. Remove the SIM card tray from the phone.
    • Remove the SIM card tray from the phone.

  3. Opening your phone will compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive. If your glass is shattered, put packing tape over the entire panel to hold it together during the removal process.
    • Opening your phone will compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive.

    • If your glass is shattered, put packing tape over the entire panel to hold it together during the removal process.

    • Lay the heated iOpener over the rear panel for about two minutes to loosen the adhesive around the edge of the glass.

    • You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.

    • Shift the iOpener to heat the remaining section of the panel for another two minutes.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

  4. Once the rear glass is hot to the touch, apply a suction cup near the bottom edge  of the glass. Lift on the suction cup to create a small gap underneath the rear glass, and insert an opening pick into the gap. Optionally, once the pick is inserted, you can add a few drops of isopropyl alcohol into the gap to help weaken the adhesive in the following steps.
    • Once the rear glass is hot to the touch, apply a suction cup near the bottom edge of the glass.

    • Lift on the suction cup to create a small gap underneath the rear glass, and insert an opening pick into the gap.

    • Optionally, once the pick is inserted, you can add a few drops of isopropyl alcohol into the gap to help weaken the adhesive in the following steps.

  5. Slide the pick along the bottom edge of the phone to slice through the adhesive securing the rear glass. Afterward, it may help to leave the pick in place and grab a second pick as you proceed to the next step. Leaving the pick inserted can help prevent the glue you just separated from re-adhering.
    • Slide the pick along the bottom edge of the phone to slice through the adhesive securing the rear glass.

    • Afterward, it may help to leave the pick in place and grab a second pick as you proceed to the next step. Leaving the pick inserted can help prevent the glue you just separated from re-adhering.

    • Re-heat the rear glass as needed to prevent the glue from cooling and hardening.

  6. US$100 이상 또는 Pro Tech Toolkit을 포함한 모든 주문의 배송은 무료입니다!

    상점 둘러보기
  7. Repeat the heating and cutting procedure for the remaining three sides of the phone. Leave an opening pick under each edge to prevent the adhesive from resealing. Leave an opening pick under each edge to prevent the adhesive from resealing.
    • Repeat the heating and cutting procedure for the remaining three sides of the phone.

    • Leave an opening pick under each edge to prevent the adhesive from resealing.

  8. Use an opening pick to slice through any remaining adhesive. Remove the rear glass.
    • Use an opening pick to slice through any remaining adhesive.

    • Remove the rear glass.

  9. Use tweezers to peel away any remaining adhesive from both the rear glass and the phone's chassis.
    • Use tweezers to peel away any remaining adhesive from both the rear glass and the phone's chassis.

    • Then, clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will help prep the surface for the new adhesive.

    • Follow this guide to reinstall the rear glass.

  10. Remove the thirteen 3.5mm Phillips #00 screws securing the midframe to the phone.
    • Remove the thirteen 3.5mm Phillips #00 screws securing the midframe to the phone.

  11. Firmly grasp the edge of the midframe assembly. Lift up on the midframe assembly while pushing down on the battery to separate the midframe assembly from the rest of the phone. While lifting the midframe, be careful to avoid snagging it on the audio jack or charging port.
    • Firmly grasp the edge of the midframe assembly.

    • Lift up on the midframe assembly while pushing down on the battery to separate the midframe assembly from the rest of the phone.

    • While lifting the midframe, be careful to avoid snagging it on the audio jack or charging port.

    • You may need to heat and apply an iOpener to the edges of the display to soften the display adhesive if midframe separation is difficult.

  12. Lift the midframe assembly up to separate it from the rest of the phone.
    • Lift the midframe assembly up to separate it from the rest of the phone.

  13. Use the pointed end of the spudger to pry up the volume button contact connectors. Use the pointed end of the spudger to pry up the volume button contact connectors.
    • Use the pointed end of the spudger to pry up the volume button contact connectors.

  14. Use the flat end of the spudger to pry the volume buttons out of the midframe. Use the flat end of the spudger to pry the volume buttons out of the midframe. Use the flat end of the spudger to pry the volume buttons out of the midframe.
    • Use the flat end of the spudger to pry the volume buttons out of the midframe.

  15. Use the pointed end of the spudger to push the button covers out of the midframe. Use the pointed end of the spudger to push the button covers out of the midframe. Use the pointed end of the spudger to push the button covers out of the midframe.
    • Use the pointed end of the spudger to push the button covers out of the midframe.

  16. Use tweezers to remove the button covers. Use tweezers to remove the button covers.
    • Use tweezers to remove the button covers.

결론

To reassemble your device, follow these instructions in reverse order. When reinstalling the rear glass, refer to the rear glass adhesive replacement guide.

다른 8명이 해당 안내서를 완성하였습니다.

Evan Noronha

회원 가입일: 2015년 02월 05일

160,733 평판

안내서 176개 작성하였습니다

iFixit iFixit 회원

Community

108 회원들

안내서 8,295개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 14

지난 30일: 50

전체 시간: 10,577