메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Samsung Galaxy S7 Edge Rear Glass Replacement

작성자 Arthur Shi (또 다른 기여자 3명)
  • 댓글 2
  • 즐겨찾기 6
  • 완료: 8

난이도

보통

단계

7

소요 시간

시간 제안??

섹션

1

플래그

0

소개

Follow this guide to replace the glass back for your Samsung Galaxy S7 Edge.

도구

해당 도구 구매

부품

해당 부품 구매

  1. Opening your phone will compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive.

    • Opening your phone will compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive.

    • Heat an iOpener and apply it to a long edge of the phone for about two minutes.

    • You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

    편집

  2. Once the back panel is warm to the touch, apply a suction cup as close to the heated edge of the phone as you can while avoiding the curved edge.

    • Once the back panel is warm to the touch, apply a suction cup as close to the heated edge of the phone as you can while avoiding the curved edge.

    • The suction cup will not adhere well on the curved portion of the glass.

    • If the phone's back cover is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.

    • Lift on the suction cup and insert an opening pick under the rear glass.

    • Due to the curved glass, you will be pushing up, rather than inserting parallel to the plane of the phone.

    • If you have trouble, apply more heat to further soften the adhesive, and try again. The adhesive cools very fast, so you may need to heat it repeatedly.

    편집

    Suction cup does not seem to work.

    Wincess Gentius - 답글

  3. Once you have the pick firmly inserted into the glass, reheat and reapply the iOpener to soften the adhesive.

    • Once you have the pick firmly inserted into the glass, reheat and reapply the iOpener to soften the adhesive.

    편집

  4. US$100 이상 또는 Pro Tech Toolkit을 포함한 모든 주문의 배송은 무료입니다!

    상점 둘러보기

  5. Slide the opening pick up along the side of the phone, separating the adhesive. Go slowly so that the tip doesn't slip out of the seam. If sliding becomes difficult, reheat and reapply the iOpener.

    • Slide the opening pick up along the side of the phone, separating the adhesive.

    • Go slowly so that the tip doesn't slip out of the seam. If sliding becomes difficult, reheat and reapply the iOpener.

    • Leave the pick in place and grab a second pick as you proceed to the next step. Leaving the pick inserted can help prevent the glue you just separated from re-adhering.

    편집

  6. Repeat the previous heating and cutting procedure for the remaining three sides of the phone. Leave an opening pick on each side as you continue to the next to prevent the adhesive from resealing. Leave an opening pick on each side as you continue to the next to prevent the adhesive from resealing.

    • Repeat the previous heating and cutting procedure for the remaining three sides of the phone.

    • Leave an opening pick on each side as you continue to the next to prevent the adhesive from resealing.

    편집

  7. Lift the glass and remove it from the phone. Lift the glass and remove it from the phone.

    • Lift the glass and remove it from the phone.

    편집

  8. To reinstall the back cover:
    이 단계에 사용된 도구:
    Tesa 61395 Tape
    $5.99

    • To reinstall the back cover:

    • First use tweezers to peel away any remaining adhesive from both the back cover and the phone's chassis.

    • Then, clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will help prep the surface for the new adhesive.

    • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

    • Replacement adhesive comes in a pre-cut sheet to match the exact contours of the back cover. If that's not available, you can use a high-bond double-sided tape, such as Tesa 61395. Be aware that this leaves gaps that are vulnerable to liquid intrusion.

    • After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

    • If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 8명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Arthur Shi

회원 가입일: 2018년 01월 03일

48,056 평판

안내서 160개 작성하였습니다

배지: 41

배지 +38개 더

팀

iFixit iFixit 회원

Community

108 회원들

안내서 8,330개 작성하였습니다

댓글 한 개

의견 추가하세요

this didn’t address the camera lens

sammann1948 - 답글

댓글 쓰기

1024

조회 통계:

지난 24시간: 20

지난 7일: 116

지난 30일: 593

전체 시간: 11,273