주요 콘텐츠로 건너뛰기

Sceptre X9 Komodo VII Power Supply Unit Replacement

필요한 것

  1. Sceptre X9 Komodo VII Power Supply Unit Replacement, Stand: 1 단계, 이미지 1/1
    • Place the monitor face down.

    • Remove the four 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the stand by pulling it out.

  2. Sceptre X9 Komodo VII Power Supply Unit Replacement: 2 단계, 이미지 1/1
    • Remove two 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the plastic bar.

  3. Sceptre X9 Komodo VII Power Supply Unit Replacement, Board Cover: 3 단계, 이미지 1/1
    • Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.

  4. Sceptre X9 Komodo VII Power Supply Unit Replacement: 4 단계, 이미지 1/3 Sceptre X9 Komodo VII Power Supply Unit Replacement: 4 단계, 이미지 2/3 Sceptre X9 Komodo VII Power Supply Unit Replacement: 4 단계, 이미지 3/3
    • Pry the monitor using the plastic opening tool to release the clips holding the cover on.

    • There are four clips on each side, four on the top, and one on the bottom.

    • You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.

    • Once all the clips have been released, remove the cover by pulling it up.

  5. Sceptre X9 Komodo VII Power Supply Unit Replacement: 5 단계, 이미지 1/2 Sceptre X9 Komodo VII Power Supply Unit Replacement: 5 단계, 이미지 2/2
    • Using the #2 Phillips screwdriver, remove the one 6mm screw.

    • Unplug the indicated cable by pulling on the base.

    • Slide the cover toward the top of the monitor.

    • Remove the cover.

  6. Sceptre X9 Komodo VII Power Supply Unit Replacement, Power Supply Unit: 6 단계, 이미지 1/1
    • Using a #2 Phillips screwdriver, remove the two 4.72 mm Phillips screws that hold the power adapter in place.

  7. Sceptre X9 Komodo VII Power Supply Unit Replacement: 7 단계, 이미지 1/3 Sceptre X9 Komodo VII Power Supply Unit Replacement: 7 단계, 이미지 2/3 Sceptre X9 Komodo VII Power Supply Unit Replacement: 7 단계, 이미지 3/3
    • Unplug the seven connections from the power supply unit by gently pulling on them.

  8. Sceptre X9 Komodo VII Power Supply Unit Replacement: 8 단계, 이미지 1/1
    • Using a #2 Phillips screwdriver, remove the screws and the wire that is attached to the ground.

    • Four 6 mm Phillips screws

    • One 8 mm Phillips screw

  9. Sceptre X9 Komodo VII Power Supply Unit Replacement: 9 단계, 이미지 1/2 Sceptre X9 Komodo VII Power Supply Unit Replacement: 9 단계, 이미지 2/2
    • Lift the power supply unit straight up to remove it from the back panel.

결론

To reassemble your device, follow these instructions in reverse order.

Jose Carrillo

회원 가입일: 09/26/12

23 평판

안내서 1개 작성함

Cal Poly, Team 16-56, Forte Fall 2012 Cal Poly, Team 16-56, Forte Fall 2012 회원

CPSU-FORTE-F12S16G56

5 회원들

안내서 13개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 5

전체 시간: 664