기기를 수리하세요 커뮤니티 상점

Shark Rotator Lift-Away Speed Brushroll Motor Replacement

소개

The brushroll motor is what powers the brushroll and makes it spin. If the brushroll is spinning, the motor may need to be replaced.

필요한 것

  1. Shark Rotator Lift-Away Speed Brushroll Motor Replacement, Brushroll: 1 단계, 이미지 1/1

    • Make sure the vacuum is turned off and unplugged before proceeding.

    • Locate the release button at the top of the vacuum pod next to the handle.

    • Use the handle to lift the pod up off of the vacuum nozzle while pressing the release button.

    • Removing the pod is optional, but it may be easier to locate blockages or access the motor and belt if you do so.

    번역하기

  2. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 2 단계, 이미지 1/2 Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 2 단계, 이미지 2/2

    • Press the Brushroll Access buttons on the top of the nozzle to reveal the brushroll compartment.

    번역하기

  3. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 3 단계, 이미지 1/2 Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 3 단계, 이미지 2/2

    • Lift the brushroll out by using the pull-tab on the left side.

    • You can test the brushroll once it has been inserted by plugging the vacuum in and running the vacuum in carpet mode. The brushroll indicator light should be a solid green color.

    번역하기

  5. Shark Rotator Lift-Away Speed Brushroll Motor Replacement, Brushroll Motor: 4 단계, 이미지 1/1

    • Remove the five 5mm Torx #9 screws on the front side.

    번역하기

  6. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 5 단계, 이미지 1/1

    • Remove the six 7.5mm Torx #20 screws on the bottom face of the nozzle.

    • A screwdriver extension may be necessary to reach the screw closest to the center of the nozzle.

    번역하기

  7. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 6 단계, 이미지 1/1

    • Remove the top panel by lifting the top piece off of the bottom.

    • There will be loud clicking noises.

    번역하기

  8. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 7 단계, 이미지 1/1

    • If you are trying to remove the belt, you may skip to the next step.

    • Remove the 7.5mm Torx #20 screw in front of the motor.

    • The motor is the gray block on the right side of the floor nozzle (when the nozzle faces towards you).

    번역하기

  9. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 8 단계, 이미지 1/2 Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 8 단계, 이미지 2/2

    • If you are trying to remove the belt, you may skip to the next step.

    • Remove the panel to reveal the motor screw.

    • Remove the 7.5mm Torx #20 motor screw.

    • Remove the motor.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 2명과 함께

Weston Mongomery

회원 가입일: 10/02/17

201 평판

안내서 2개 작성하였습니다

배지: 4

+1개 배지 추가

팀

Cal Poly, Team S15-G7, Livingston Fall 2017 Cal Poly, Team S15-G7, Livingston Fall 2017 회원

CPSU-LIVINGSTON-F17S15G7

4 회원들

안내서 10개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 6

30일 전: 21

전체 시간: 3,716