기기를 수리하세요 커뮤니티 상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

Shark Rotator Powered Lift-Away Speed Belt Replacement

소개

The Shark Rotator Powered Lift-Away has one rotatory belt. The belt is responsible for the mechanical rotations of the brushroll. Without it, the vacuum will not function. The vacuum's belt is designed to last approximately 7 years. Replacement of the belt is needed to keep the vacuum at optimal working condition. This replacement guide demonstrates how to replace the belt in the vacuum.

필요한 것

  1. Shark Rotator Powered Lift-Away Speed Belt Replacement, Belt: 1 단계, 이미지 1/3 Shark Rotator Powered Lift-Away Speed Belt Replacement, Belt: 1 단계, 이미지 2/3 Shark Rotator Powered Lift-Away Speed Belt Replacement, Belt: 1 단계, 이미지 3/3

    • Turn the vacuum on its side.

    • Using a quarter, twist the three green locks to the unlock position.

    • Pull the bottom roller brush cover to open the vacuum.

    번역하기

  2. Shark Rotator Powered Lift-Away Speed Belt Replacement: 2 단계, 이미지 1/1

    • Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.

    번역하기

  3. Shark Rotator Powered Lift-Away Speed Belt Replacement: 3 단계, 이미지 1/2 Shark Rotator Powered Lift-Away Speed Belt Replacement: 3 단계, 이미지 2/2

    • Remove the three 14.3 mm screws with a T20 screwdriver.

    번역하기

  4. Shark Rotator Powered Lift-Away Speed Belt Replacement: 4 단계, 이미지 1/1

    • Remove the two 14.3 mm screws under the wheels with a T20 screwdriver bit.

    번역하기

  5. Shark Rotator Powered Lift-Away Speed Belt Replacement: 5 단계, 이미지 1/1

    • Remove the two 15.9 mm screws from behind the wheels with a T20 bit screwdriver.

    번역하기

  6. Shark Rotator Powered Lift-Away Speed Belt Replacement: 6 단계, 이미지 1/1

    • Remove the single 13.4 mm small screw behind the roller brush with a PH0 screwdriver bit.

    번역하기

  8. Shark Rotator Powered Lift-Away Speed Belt Replacement: 7 단계, 이미지 1/1

    • Remove the single 13.4 mm screw from behind the belted end of the roller brush with a T20 screwdriver bit.

    번역하기

  9. Shark Rotator Powered Lift-Away Speed Belt Replacement: 8 단계, 이미지 1/3 Shark Rotator Powered Lift-Away Speed Belt Replacement: 8 단계, 이미지 2/3 Shark Rotator Powered Lift-Away Speed Belt Replacement: 8 단계, 이미지 3/3

    • Turn the vacuum around.

    • Using a spudger, pry the top of the vacuum cover off. There are three tabs behind each of the clear rectangles below the headlights.

    번역하기

  10. Shark Rotator Powered Lift-Away Speed Belt Replacement: 9 단계, 이미지 1/2 Shark Rotator Powered Lift-Away Speed Belt Replacement: 9 단계, 이미지 2/2

    • Remove both of the headlight covers with the spudger.

    번역하기

  11. Shark Rotator Powered Lift-Away Speed Belt Replacement: 10 단계, 이미지 1/3 Shark Rotator Powered Lift-Away Speed Belt Replacement: 10 단계, 이미지 2/3 Shark Rotator Powered Lift-Away Speed Belt Replacement: 10 단계, 이미지 3/3

    • Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel.

    번역하기

  12. Shark Rotator Powered Lift-Away Speed Belt Replacement: 11 단계, 이미지 1/1

    • Remove the two 13.4 mm screws with a T20 bit screwdriver.

    번역하기

  13. Shark Rotator Powered Lift-Away Speed Belt Replacement: 12 단계, 이미지 1/1

    • Remove the single 13.4 mm screw located next to where the belt was detached, securing the motor in place, with a PH1 screwdriver.

    번역하기

  14. Shark Rotator Powered Lift-Away Speed Belt Replacement: 13 단계, 이미지 1/3 Shark Rotator Powered Lift-Away Speed Belt Replacement: 13 단계, 이미지 2/3 Shark Rotator Powered Lift-Away Speed Belt Replacement: 13 단계, 이미지 3/3

    • Remove the visible side of the belt from the gear with a spudger.

    번역하기

  15. Shark Rotator Powered Lift-Away Speed Belt Replacement: 14 단계, 이미지 1/1

    • Remove the grey panel from the opposite side, by uncrewing the single 13.4 mm screw with a PH1 screwdriver. This will release the container for the roller brush and belt motor.

    번역하기

  16. Shark Rotator Powered Lift-Away Speed Belt Replacement: 15 단계, 이미지 1/2 Shark Rotator Powered Lift-Away Speed Belt Replacement: 15 단계, 이미지 2/2

    • Using the spudger, push the white end cap out of the clear plastic by placing the spudger on the roller brush side and pushing the cap outward.

    번역하기

  17. Shark Rotator Powered Lift-Away Speed Belt Replacement: 16 단계, 이미지 1/2 Shark Rotator Powered Lift-Away Speed Belt Replacement: 16 단계, 이미지 2/2

    • Remove the belt from the gear.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Dakota Rodriguez-Ransom

회원 가입일: 10/08/18

605 평판

안내서 2개 작성하였습니다

배지: 8

배지 +5개 더

팀

Cal Poly, Team S4-G6, White Fall 2018 Cal Poly, Team S4-G6, White Fall 2018 회원

CPSU-WHITE-F18S4G6

4 회원들

안내서 12개 작성하였습니다

댓글 2개

Where can we buy belts in UK?

Greg Norman - 답글

where cn i get a belt for this vaccum

Annie Pappineau - 답글

댓글 쓰기

조회 통계:

24 시간 전: 26

7일 전: 210

30일 전: 1,094

전체 시간: 37,780