주요 콘텐츠로 건너뛰기

부품

지정된 부품이 없습니다.

  1. Push the gold bar, located in the top of the device, out of the carbonating block. You can use the end of your screwdriver to push this piece out. You can use the end of your screwdriver to push this piece out.
    • Push the gold bar, located in the top of the device, out of the carbonating block.

    • You can use the end of your screwdriver to push this piece out.

  2. Slide the yellow battery cover up and away to remove it from the device. Slide the yellow battery cover up and away to remove it from the device. Slide the yellow battery cover up and away to remove it from the device.
    • Slide the yellow battery cover up and away to remove it from the device.

  3. Unhook the bottom piece of the plastic arm on each side of the device. Unhook the bottom piece of the plastic arm on each side of the device.
    • Unhook the bottom piece of the plastic arm on each side of the device.

  4. Lift the top of the plastic arm with the spudger and remove it on both sides. Lift the top of the plastic arm with the spudger and remove it on both sides.
    • Lift the top of the plastic arm with the spudger and remove it on both sides.

  5. Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger. Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger.
    • Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger.

  6. Remove the plastic oval and the spring within it. Remove the plastic oval and the spring within it.
    • Remove the plastic oval and the spring within it.

  7. Pull the loader tab cover down and away from the rest of the carbonating block. Pull the loader tab cover down and away from the rest of the carbonating block.
    • Pull the loader tab cover down and away from the rest of the carbonating block.

  8. Remove the three 17.9 mm screws located on the right side.
    • Remove the three 17.9 mm screws located on the right side.

    • These screws may be difficult to access.

  9. Unhook the four clips on the top of the carbonating block and remove the plastic cover. Unhook the four clips on the top of the carbonating block and remove the plastic cover.
    • Unhook the four clips on the top of the carbonating block and remove the plastic cover.

  10. Lift the clips located on both sides with the plastic spudger. Slide the front cover off. Lift the clips located on both sides with the plastic spudger. Slide the front cover off. Lift the clips located on both sides with the plastic spudger. Slide the front cover off.
    • Lift the clips located on both sides with the plastic spudger. Slide the front cover off.

  11. Unhook the silver spring arms on both sides of the device by pushing down. Unhook the silver spring arms on both sides of the device by pushing down.
    • Unhook the silver spring arms on both sides of the device by pushing down.

  12. Grip the right and left sides of the device and pull it into two identical halves.
    • Grip the right and left sides of the device and pull it into two identical halves.

    • Once these two pieces are apart, all remaining internal components will fall out of the device.

  13. Pull the foam pad up and remove it from the front side of the carbonation component. Pull the foam pad up and remove it from the front side of the carbonation component. Pull the foam pad up and remove it from the front side of the carbonation component.
    • Pull the foam pad up and remove it from the front side of the carbonation component.

  14. Remove the six 17.7 mm screws from the underside of the loader tab piece.
    • Remove the six 17.7 mm screws from the underside of the loader tab piece.

  15. Pull the loader tab out of  the nozzle. Pull the loader tab out of  the nozzle. Pull the loader tab out of  the nozzle.
    • Pull the loader tab out of the nozzle.

결론

To reassemble your device, follow these instructions in reverse order.

Angela Mossgrove

회원 가입일: 2017년 02월 20일

536 평판

안내서 3개 작성하였습니다

USF Tampa, Team S1-G4, Leahy Spring 2017 USF Tampa, Team S1-G4, Leahy Spring 2017 회원

USFT-LEAHY-S17S1G4

3 회원들

안내서 9개 작성하였습니다

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 9

전체 시간: 192