주요 콘텐츠로 건너뛰기

기기를 수리하세요

수리할 권리

상점

  1. Remove the two Phillips head, 2.93 mm long screws at the bottom of the camera.
    • Remove the two Phillips head, 2.93 mm long screws at the bottom of the camera.

    • Make sure the battery compartment door is in lock position.

  2. Turn the camera sideways so the left side is fasning upwards, remove the two Phillips head, 2.93 mm screws.
    • Turn the camera sideways so the left side is fasning upwards, remove the two Phillips head, 2.93 mm screws.

  3. Now turn the device so the opposite side is fasning upwards and remove the last two Phillips head, 2.93 mm screws.
    • Now turn the device so the opposite side is fasning upwards and remove the last two Phillips head, 2.93 mm screws.

  4. To remove the front cover, use a plastic opening tool gently pry the top cover. Then gently lift the cover off.
    • To remove the front cover, use a plastic opening tool gently pry the top cover.

    • Then gently lift the cover off.

  5. To remove the back case cover from the body. First use a plastic opening tool gently pry along the side of the camera.
    • To remove the back case cover from the body.

    • First use a plastic opening tool gently pry along the side of the camera.

    • Then slowly and gently lift the cover off.

  6. These are the two cables connecting the LCD screen to the motherboard below the screen.
    • These are the two cables connecting the LCD screen to the motherboard below the screen.

  7. Remove the LCD screen from the side opppsite the battery terminals. Watch for the two cords mentioned in the previous step. These will still be connected.The side will flip up as shown in the next step.
    • Remove the LCD screen from the side opppsite the battery terminals. Watch for the two cords mentioned in the previous step. These will still be connected.The side will flip up as shown in the next step.

  8. Pull these two cords straight back to disconnect them from the respective housings. Caution: The housing do not need to be moved or adjusted in anyway. Do not pull the cords at an angle, it can destroy the cords and the housing. Pull Straight Back!
    • Pull these two cords straight back to disconnect them from the respective housings. Caution: The housing do not need to be moved or adjusted in anyway. Do not pull the cords at an angle, it can destroy the cords and the housing. Pull Straight Back!

  9. This is what the camera should look like after 2 cords and the screen have been removed. The lens cord is being held to the side for a clearer view.
    • This is what the camera should look like after 2 cords and the screen have been removed. The lens cord is being held to the side for a clearer view.

  10. After camera is disassembled the capacitor will need to be removed. Use tweezers to gently pull away the ribbon from the connector. After camera is disassembled the capacitor will need to be removed. Use tweezers to gently pull away the ribbon from the connector.
    • After camera is disassembled the capacitor will need to be removed. Use tweezers to gently pull away the ribbon from the connector.

  11. With the camera lying face down, separate the tape that connects the rest of the lens using tweezers.
    • With the camera lying face down, separate the tape that connects the rest of the lens using tweezers.

    • Gently remove the lens display using your fingers out of the camera body.

    • Take caution not to damage any of the ribbon cables that might still be attached.

    • The lens assembly is now removed from the camera body and is able to be replaced if necessary.

결론

To reassemble your device, follow these instructions in reverse order.

다른 4명이 해당 안내서를 완성하였습니다.

Gonzalo

회원 가입일: 2015년 01월 26일

209 평판

안내서 1개 작성함

USF Tampa, Team 9-1, Brown Winter 2015 USF Tampa, Team 9-1, Brown Winter 2015 회원

USFT-BROWN-W15S9G1

5 회원들

안내서 10개 작성하였습니다

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 7

전체 시간: 1,024