기기를 수리하세요 커뮤니티 상점

Sony NEX-7 LCD Assembly Replacement

단지 전제 조건
이 안내서는 다른 가이드의 선행 작업으로 사용하기 위한 것입니다. 그 자체로는 불완전합니다.

필요한 것

  1. Sony NEX-7 LCD Assembly Replacement, LCD Assembly: 1 단계, 이미지 1/1

    • Remove the two 3/32" #00 screws located next to the viewfinder using the Phillips #00 screwdriver.

    편집

  2. Sony NEX-7 LCD Assembly Replacement: 2 단계, 이미지 1/1

    • Use a Phillips #00 screwdriver to remove the two screws from the right side of the camera below the D ring:

    • The 5/32" upper screw

    • The 3/32" lower screw

    편집

  3. Sony NEX-7 LCD Assembly Replacement: 3 단계, 이미지 1/1

    • Remove two more 3/32" #00 screws from the bottom of the camera using the Phillips #00 screwdriver.

    편집

  5. Sony NEX-7 LCD Assembly Replacement: 4 단계, 이미지 1/1

    • Remove two more 3/32" #00 screws from the metal bracket on the left side of the camera using the Phillips #00 screwdriver.

    편집

  6. Sony NEX-7 LCD Assembly Replacement: 5 단계, 이미지 1/1
    이 단계에 사용된 도구:
    Tweezers
    $4.99
    구매

    • Unplug the orange ribbon cable on the top right of the camera next to the metal bracket by applying tweezers to the tabs on either side of the plug.

    편집

  7. Sony NEX-7 LCD Assembly Replacement: 6 단계, 이미지 1/1

    • Before pulling off the assembly, fold the rightmost tab of the flexible circuit board away from the metal bracket.

    편집

  8. Sony NEX-7 LCD Assembly Replacement: 7 단계, 이미지 1/2 Sony NEX-7 LCD Assembly Replacement: 7 단계, 이미지 2/2

    • The LCD assembly is attached with a concealed ribbon cable, so be gentle when you remove it.

    • The D ring brackets on either side are not attached, only held in mechanically. Once the LCD assembly starts to come out, they will detach.

    • Pull on the D rings on either side of the camera to start removing the assembly.

    • Once the brackets are cleared from black shell, take them off and set them aside.

    • Continue to remove the screen assembly.

    편집

  9. Sony NEX-7 LCD Assembly Replacement: 8 단계, 이미지 1/1

    • With the camera face down, move the assembly away from you to get a clear view of the wide ribbon cable.

    • Unplug the cable by applying tweezers to the tabs on either side of the plug.

    • Set the LCD assembly aside.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 7명과 함께

Jay Miley

회원 가입일: 04/22/14

5,058 평판

안내서 13개 작성하였습니다

배지: 27

배지 +24개 더

팀

Cal Poly, Team 10-55, Amido Spring 2014 Cal Poly, Team 10-55, Amido Spring 2014 회원

CPSU-AMIDO-S14S10G55

4 회원들

안내서 31개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 4

30일 전: 9

전체 시간: 73