주요 콘텐츠로 건너뛰기

소개

This guide give instructions on how to locate the speaker for removal and/or repair.

부품

지정된 부품이 없습니다.

  1. Speaker, Battery: 1 단계, 이미지 1/1
    • Flip over the phone so that the back is facing up.

    • Pressing your thumb against the back cover, slide the cover off of the phone.

  2. Speaker: 2 단계, 이미지 1/1
    • Remove the phone's battery.

  3. Speaker, Front LCD Display: 3 단계, 이미지 1/3 Speaker, Front LCD Display: 3 단계, 이미지 2/3 Speaker, Front LCD Display: 3 단계, 이미지 3/3
    • With the phone closed, run a plastic opening tool along the seam of the top half of the phone.

    • Make sure to disconnect each of the five clips before proceeding to the next step.

    • There are two clips on each side of the phone and one on the top.

  4. Speaker: 4 단계, 이미지 1/2 Speaker: 4 단계, 이미지 2/2
    • Remove the four 3.2 mm screws from the front panel using a T6 Torx screwdriver.

    • The fourth screw is located under a fold in the ribbon cable.

  5. Speaker: 5 단계, 이미지 1/3 Speaker: 5 단계, 이미지 2/3 Speaker: 5 단계, 이미지 3/3
    • Starting in the lower right corner, slowly begin to lift the tape that is holding down the front LCD and cables.

    • Be careful around the two ribbon cables attached to the tape. These cables are fragile.

    • Lift the tape from the board.

  6. Speaker: 6 단계, 이미지 1/1
    • Using a plastic opening tool, lift the ribbon cable connection below the front LCD.

  7. Speaker: 7 단계, 이미지 1/3 Speaker: 7 단계, 이미지 2/3 Speaker: 7 단계, 이미지 3/3
    • Using a plastic opening tool, slowly pry the LCD display from the bottom, releasing it from the glue that is holding it to the board.

  8. Speaker, Inner LCD Display: 8 단계, 이미지 1/1
    • Locate the ribbon cable connection in the upper right hand corner of the board.

    • Using a plastic opening tool, lift off the cable from the board.

    • Be gentle and make sure not to rip the ribbon cable.

  9. Speaker: 9 단계, 이미지 1/2 Speaker: 9 단계, 이미지 2/2
    • Using a plastic opening tool, slowly work the board off the mounts holding it to the frame.

    • Flip the board over to reveal the main display.

  10. Speaker: 10 단계, 이미지 1/1
    • Locate the ribbon cable for the main display on the bottom of the board.

    • Slowly lift off the ribbon connector from its housing using a plastic opening tool.

  11. Speaker: 11 단계, 이미지 1/2 Speaker: 11 단계, 이미지 2/2
    • Slowly wedge the plastic opening tool under the bottom of the main display.

    • Separate the display from the glue lifting it off the board.

  12. Speaker, Speaker: 12 단계, 이미지 1/1
    • Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Andrew

회원 가입일: 2010년 10월 04일

397 평판

안내서 4개 작성하였습니다

Cal Poly, Team 4-46, Amido Fall 2010 Cal Poly, Team 4-46, Amido Fall 2010 회원

CPSU-AMIDO-F10S4G46

4 회원들

안내서 14개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 4

전체 시간: 504