Table Lamp Cord Replacement - iFixit 수리 안내서

소개

This step-by-step guide teaches the users two procedures: removing and replacing an old lamp cord and attaching a new cord to the socket.

필요한 것

1 단계 Cord

Table Lamp Cord Replacement, Cord: 1 단계, 이미지 1/2

Table Lamp Cord Replacement, Cord: 1 단계, 이미지 2/2

Required materials: AAMP rewire kit, light bulb (not pictured), lamp shade (optional).
The AAMP lamp rewire kit should include a new cord, a socket shell, a socket interior and bottle adaptors. (Refer the second image to view the contents of the kit).

2 단계

Table Lamp Cord Replacement: 2 단계, 이미지 1/1

Caution! Before removing the lightbulb, ensure that the lamp is unplugged.
Cut the old lamp wire using scissors.
Remove the cord from the lamp.
Dispose the cord.

3 단계

Table Lamp Cord Replacement: 3 단계, 이미지 1/2

Table Lamp Cord Replacement: 3 단계, 이미지 2/2

Thread the new wire through the hole on the bottom of the lamp. Pull it out through the top of the lamp base. (Refer the first image to get a better understanding.)
Place the old check ring on top of the lamp with the wire threaded through it. (Refer the second image to see the check ring.)

4 단계

Table Lamp Cord Replacement: 4 단계, 이미지 1/2

Table Lamp Cord Replacement: 4 단계, 이미지 2/2

Place the lock nut at the end of the lamp nipple and turn it clockwise.
Thread the lock nut a quarter of the way through the lamp nipple.

5 단계

Table Lamp Cord Replacement: 5 단계, 이미지 1/2

Table Lamp Cord Replacement: 5 단계, 이미지 2/2

Ensure that the lamp cord sticks through the top of the lamp base.
Insert the lamp nipple and the lock nut into the bottle, in such a way that one-fourth inch of the lamp nipple faces up.

6 단계

Table Lamp Cord Replacement: 6 단계, 이미지 1/1

Insert the socket in the lamp nipple.
Tighten the socket by turning it clockwise until it reaches the lock nut.

7 단계

Table Lamp Cord Replacement: 7 단계, 이미지 1/1

Pull either ends of the wire so that you have about 2-3 inches of the wire separated.

8 단계

Table Lamp Cord Replacement: 8 단계, 이미지 1/1

Tie an underwriter's knot in the two separated pieces of wire.
How to tie the knot: Form a loop using the first wire. Take the second wire and form a loop around the first. Pass the tail of the second wire through the loop of the first.

9 단계

Table Lamp Cord Replacement: 9 단계, 이미지 1/1

Check both the conductors at the end of the wire. Find the ribbed conductor and wrap it around the silver-colored screw. Connect the other conductor to the brass-colored screw.
Tighten both of the screws in a clockwise direction. Make sure the conductors are securely under the screw head.

10 단계

Table Lamp Cord Replacement: 10 단계, 이미지 1/2

Table Lamp Cord Replacement: 10 단계, 이미지 2/2

Place the socket shell (with paper liner) over the socket interior. Snap it into correct position. Listen for clicks to make sure that the shell is locked properly.
The socket should snap together to form one piece.

11 단계

Table Lamp Cord Replacement: 11 단계, 이미지 1/1

Caution: Be sure that the rewired lamp is not plugged at this step.
Insert the new light bulb into the socket. Plug the cord and turn it on.

결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 7명과 함께

Aysha Vear

회원 가입일: 11/04/15

195 평판

안내서 1개 작성함

배지 +2개 더

팀

University of Maine, Team 1-3, Diaz Fall 2015 University of Maine, Team 1-3, Diaz Fall 2015 회원

UMAINE-DIAZ-F15S1G3

3 회원들

안내서 1개 작성하였습니다

댓글 0개

조회 통계:

24 시간 전: 1

7일 전: 24

30일 전: 93

전체 시간: 6,983