기기를 수리하세요 커뮤니티 상점

TomTom One XL Charging Port Replacement

소개

This guide will show you how to replace or reconnect the charging port to the motherboard.

필요한 것

  1. TomTom One XL Charging Port Replacement, Back Panel: 1 단계, 이미지 1/2 TomTom One XL Charging Port Replacement, Back Panel: 1 단계, 이미지 2/2

    • Remove the 4 .4mm screws on the back of the device.

    편집

  2. TomTom One XL Charging Port Replacement: 2 단계, 이미지 1/1

    • Using the palate knife tool, pry the back from the LCD screen. Apply a moderate pressure to separate them.

    • You can rotate TOMTOM XL to make prying back off easier.

    • Be careful not to injure the two wires connecting the pieces.

    편집

  3. TomTom One XL Charging Port Replacement: 3 단계, 이미지 1/1

    • After prying both halves apart, they will be connected by two wires.

    • Carefully set the two halves next to each other making sure not to stress or damage the wires.

    편집

  5. TomTom One XL Charging Port Replacement: 4 단계, 이미지 1/2 TomTom One XL Charging Port Replacement: 4 단계, 이미지 2/2
    이 단계에 사용된 도구:
    Tweezers
    $4.99
    구매

    • Using the tweezers separate the wires connecting the battery and speaker to the mother board.

    • Be gentle while pulling the wires out, the plugs are easily injured.

    편집

  6. TomTom One XL Charging Port Replacement, Charging Port: 5 단계, 이미지 1/2 TomTom One XL Charging Port Replacement, Charging Port: 5 단계, 이미지 2/2

    • If this is your first time solder then refer to IFixIt's safety guide.

    • Locate where the charger port goes on the circuit board.

    • Locate the four connecter on circuit board and charger port which need to be soldered.

    • Don't forget, the soldering iron is hot.

    편집

  7. TomTom One XL Charging Port Replacement: 6 단계, 이미지 1/3 TomTom One XL Charging Port Replacement: 6 단계, 이미지 2/3 TomTom One XL Charging Port Replacement: 6 단계, 이미지 3/3

    • Using your plastic opening tool press down firmly on the top of the charger port.

    • While the soldering iron is hot press it again the four corners of the charger port.

    • Don't touch the charger port with your hands, it may have heated up during soldering.

    편집

  8. TomTom One XL Charging Port Replacement: 7 단계, 이미지 1/3 TomTom One XL Charging Port Replacement: 7 단계, 이미지 2/3 TomTom One XL Charging Port Replacement: 7 단계, 이미지 3/3

    • Let the circuit board and charger port cool down for a few minutes.

    • Lift circuit board up, after making sure its cool, to see if four corners are all connected.

    • Plug in the charger to make sure it works, if not repeat steps and make sure the port is making a clean connection.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 2명과 함께

DeVhan

회원 가입일: 03/11/15

401 평판

안내서 4개 작성하였습니다

배지: 4

+1개 배지 추가

팀

Colorado Springs, Team 9-6, Panko Spring 2015 Colorado Springs, Team 9-6, Panko Spring 2015 회원

UCCS-PANKO-S15S9G6

3 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 8

전체 시간: 2,410