메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Toshiba Satellite A75-S226 Keyboard Replacement

작성자 Garrett Gudgel (또 다른 기여자 11명)
  • 댓글 0
  • 즐겨찾기 6

난이도

보통

단계

5

소요 시간

4 - 5 분

섹션

1

플래그

0

도구

해당 도구 구매

부품

부품은 필요하지 않습니다.

  1. Use the plastic opening tool to lift up the top panel all the way along the keyboard until it loosens. It may be helpful to first pry at the rear of the hinge covers (not shown) to release them. Then Insert the plastic opening tool underneath the top panel's sides and then front edge. It may be helpful to first pry at the rear of the hinge covers (not shown) to release them. Then Insert the plastic opening tool underneath the top panel's sides and then front edge.

    • Use the plastic opening tool to lift up the top panel all the way along the keyboard until it loosens.

    • It may be helpful to first pry at the rear of the hinge covers (not shown) to release them. Then Insert the plastic opening tool underneath the top panel's sides and then front edge.

    편집

  2. Remove the top panel by popping the panel out the top left socket, then do the same with the right side. Remove the top panel by popping the panel out the top left socket, then do the same with the right side.

    • Remove the top panel by popping the panel out the top left socket, then do the same with the right side.

    편집

  3. US$100 이상 또는 Pro Tech Toolkit을 포함한 모든 주문의 배송은 무료입니다!

    상점 둘러보기

  4. Remove the two 3.67 mm screws from the top corners of the keyboard. Remove the two 3.67 mm screws from the top corners of the keyboard. Remove the two 3.67 mm screws from the top corners of the keyboard.

    • Remove the two 3.67 mm screws from the top corners of the keyboard.

    편집

  5. Use fingers to lift up the keyboard from the top.

    • Use fingers to lift up the keyboard from the top.

    • Do not try to remove the keyboard completely because it is still attached to the motherboard.

    편집

  6. Remove the cable connecting the keyboard with the motherboard. Be aware of the locking tabs on each side of the ribbon-cable connector—they slide back about 2mm to free the cable. Lift up and remove the keyboard.

    • Remove the cable connecting the keyboard with the motherboard.

    • Be aware of the locking tabs on each side of the ribbon-cable connector—they slide back about 2mm to free the cable.

    • Lift up and remove the keyboard.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 11명과 함께

Garrett Gudgel

회원 가입일: 2010년 10월 05일

714 평판

안내서 13개 작성하였습니다

배지: 14

배지 +11개 더

팀

Cal Poly, Team 4-43, Amido Fall 2010 Cal Poly, Team 4-43, Amido Fall 2010 회원

CPSU-AMIDO-F10S4G43

5 회원들

안내서 13개 작성하였습니다

댓글 0개

의견 추가하세요
조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 3

전체 시간: 4,034