주요 콘텐츠로 건너뛰기

Uniden D1483-3BK Circuit Board/Screen Replacement

필요한 것

  1. Uniden D1483-3BK Circuit Board/Screen Replacement, Battery: 1 단계, 이미지 1/1
    • Set the phone with dial keys facing downward.

  2. Uniden D1483-3BK Circuit Board/Screen Replacement: 2 단계, 이미지 1/2 Uniden D1483-3BK Circuit Board/Screen Replacement: 2 단계, 이미지 2/2
    • Slide the battery cover toward the bottom of the phone.

    • Lift and remove the back cover from the phone.

  3. Uniden D1483-3BK Circuit Board/Screen Replacement: 3 단계, 이미지 1/1
    • Remove the battery from its compartment.

    • Pinch the end of cord where the battery is attached to the phone and pull up gently.

  4. Uniden D1483-3BK Circuit Board/Screen Replacement, Handset Case: 4 단계, 이미지 1/2 Uniden D1483-3BK Circuit Board/Screen Replacement, Handset Case: 4 단계, 이미지 2/2
    • Remove the two 9mm Phillips #1 screws in the battery compartment.

  5. Uniden D1483-3BK Circuit Board/Screen Replacement: 5 단계, 이미지 1/3 Uniden D1483-3BK Circuit Board/Screen Replacement: 5 단계, 이미지 2/3 Uniden D1483-3BK Circuit Board/Screen Replacement: 5 단계, 이미지 3/3
    • Use the plastic opening tool to carefully separate the two halves of the case.

    • Slowly work around the entire case to fully separate the halves before pulling them apart.

    • Wires inside the case hold the two halves together, tearing these wires will lead to a need for additional repair.

  6. Uniden D1483-3BK Circuit Board/Screen Replacement: 6 단계, 이미지 1/2 Uniden D1483-3BK Circuit Board/Screen Replacement: 6 단계, 이미지 2/2
    • Carefully remove the 9mm Phillips #1 screw from the top corner of the circuit board.

  7. Uniden D1483-3BK Circuit Board/Screen Replacement: 7 단계, 이미지 1/2 Uniden D1483-3BK Circuit Board/Screen Replacement: 7 단계, 이미지 2/2
    • Carefully grasp either side of the circuit board and lift it straight out of the front half of the case.

    • Set the board in the lower half of the case.

  8. Uniden D1483-3BK Circuit Board/Screen Replacement, Circuit Board/Screen: 8 단계, 이미지 1/1
    • Set the circuit board on the table with the screen facing down.

  9. Uniden D1483-3BK Circuit Board/Screen Replacement: 9 단계, 이미지 1/1
    • Using the desoldering braid and soldering iron, remove the solder around the cable for the speaker.

    • When installing the new board, use the soldering iron and solder to reattach the speaker cables.

결론

To reassemble your device, follow these instructions in reverse order.

다른 6명이 해당 안내서를 완성하였습니다.

Arbitrary Name

회원 가입일: 01/28/15

1,083 평판

안내서 4개 작성하였습니다

Penn State, Team 1-8, Kaschak Winter 2015 Penn State, Team 1-8, Kaschak Winter 2015 회원

PSU-KASCHAK-W15S1G8

4 회원들

안내서 8개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 3

전체 시간: 293