메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Welch Allyn Connex Vital Signs Monitor 6000 Stand Replacement

작성자 Sam Goldheart (및 기여자 1명)
  • 댓글 0
  • 즐겨찾기 2

난이도

쉬움

단계

10

소요 시간

시간 제안??

섹션

1

플래그

0

소개

Use this guide to remove the Connex Vital Signs Monitor from the Welch Allen office cart stand.

PLEASE NOTE: This repair guide was developed by the iFixit team based on Welch Allyn's own service manual. Neither iFixit nor this repair guide is endorsed by or affiliated with Welch Allyn.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Unplug the AC power connection cable. Unplug the AC power connection cable.

    • Unplug the AC power connection cable.

    편집

  2. Place your thumb and forefinger on the blood pressure (NIBP) hose connector. Squeeze the side tabs until the connector releases. Always grasp the hose by the connector. Do not pull on the hose itself. Pull the connector away from the connector port.

    • Place your thumb and forefinger on the blood pressure (NIBP) hose connector. Squeeze the side tabs until the connector releases.

    • Always grasp the hose by the connector. Do not pull on the hose itself.

    • Pull the connector away from the connector port.

    편집

  3. Place your thumb and forefinger on the Pulse oximetry (SpO2 or combined SpO2/SpHb) cable connector. Squeeze the side tabs until the connector releases. Always grasp the cable by the connector. Do not pull on the cable itself. Pull the connector away from the connector port.

    • Place your thumb and forefinger on the Pulse oximetry (SpO2 or combined SpO2/SpHb) cable connector. Squeeze the side tabs until the connector releases.

    • Always grasp the cable by the connector. Do not pull on the cable itself.

    • Pull the connector away from the connector port.

    편집

  4. Grasp the temperature probe and pull it up to remove it from the monitor. Grasp the temperature probe and pull it up to remove it from the monitor.

    • Grasp the temperature probe and pull it up to remove it from the monitor.

    편집

  6. Remove the cover of the temperature module by pressing the tab and sliding the cover to the right. Remove the cover of the temperature module by pressing the tab and sliding the cover to the right. Remove the cover of the temperature module by pressing the tab and sliding the cover to the right.

    • Remove the cover of the temperature module by pressing the tab and sliding the cover to the right.

    편집

  7. Depress the spring tab on the temperature probe cable connector and withdraw it from the probe port. Depress the spring tab on the temperature probe cable connector and withdraw it from the probe port. Depress the spring tab on the temperature probe cable connector and withdraw it from the probe port.

    • Depress the spring tab on the temperature probe cable connector and withdraw it from the probe port.

    편집

  8. Remove the flathead screw on the USB networking door.

    • Remove the flathead screw on the USB networking door.

    • Loosen the captive Phillips #2 screw securing the monitor to the stand.

    편집

  9. Holding the monitor securely, open the USB networking door.

    • Holding the monitor securely, open the USB networking door.

    • You may have to lift the monitor slightly to allow the door to swing out from the stand mount.

    편집

  10. Detach any accessory USB cables from USB ports on the monitor. Detach any accessory USB cables from USB ports on the monitor.

    • Detach any accessory USB cables from USB ports on the monitor.

    편집

  11. Slide the monitor off of the stand tray. Slide the monitor off of the stand tray. Slide the monitor off of the stand tray.

    • Slide the monitor off of the stand tray.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 1명과 함께

Sam Goldheart

회원 가입일: 2012년 10월 18일

384,871 평판

안내서 544개 작성하였습니다

배지: 48

배지 +45개 더

팀

iFixit iFixit 회원

Community

104 회원들

안내서 9,222개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 1

지난 30일: 4

전체 시간: 450