물건을 수리하세요 커뮤니티 상점

WowWee MiP Robot LED Light Replacement

소개

The LED light on the MiP indicates what mode the robot is in. If this light is malfunctioning, using the MiP is difficult.

필요한 것

  1. WowWee MiP Robot LED Light Replacement, Battery: 1 단계, 이미지 2개 중 1개 WowWee MiP Robot LED Light Replacement, Battery: 1 단계, 이미지 2개 중 2개

    • Remove the three 12.0 mm Phillips # 2 screws from the battery cover.

    편집

  2. WowWee MiP Robot LED Light Replacement: 2 단계, 이미지 2개 중 1개 WowWee MiP Robot LED Light Replacement: 2 단계, 이미지 2개 중 2개

    • Carefully pull the battery pack from the robot.

    • Remove the batteries from the battery pack.

    편집

  3. WowWee MiP Robot LED Light Replacement, Wheel: 3 단계, 이미지 2개 중 1개 WowWee MiP Robot LED Light Replacement, Wheel: 3 단계, 이미지 2개 중 2개

    • Use a metal spudger to carefully pry off the hubcap without marring the plastic wheel or hubcap.

    • This plastic material is not replaceable. Any damage will be noticeable.

    편집

  4. WowWee MiP Robot LED Light Replacement: 4 단계, 이미지 2개 중 1개 WowWee MiP Robot LED Light Replacement: 4 단계, 이미지 2개 중 2개

    • Remove the 12.0 mm Phillips #2 screw.

    • Hold the wheel in place, or it will rotate as you attempt to remove the screw.

    편집

  5. WowWee MiP Robot LED Light Replacement: 5 단계, 이미지 1개 중 1개

    • Pull the wheel off of the square axle.

    • Do not use excessive force while removing the wheel. Pulling too hard on the wheel can damage the axle.

    편집

  7. WowWee MiP Robot LED Light Replacement, WowWee MiP Robot Body Disassembly: 6 단계, 이미지 2개 중 1개 WowWee MiP Robot LED Light Replacement, WowWee MiP Robot Body Disassembly: 6 단계, 이미지 2개 중 2개

    • Remove the eight 9.3 mm Phillips #1 screws from the back of the robot.

    편집

  8. WowWee MiP Robot LED Light Replacement: 7 단계, 이미지 3개 중 1개 WowWee MiP Robot LED Light Replacement: 7 단계, 이미지 3개 중 2개 WowWee MiP Robot LED Light Replacement: 7 단계, 이미지 3개 중 3개

    • Remove the arms from the body.

    • Carefully open the body compartment.

    • Open the compartment slowly. There are wires connecting the two body pieces together. If pulled too hard, the wires and/or the motherboard could be damaged.

    편집

  9. WowWee MiP Robot LED Light Replacement: 8 단계, 이미지 1개 중 1개
    이 단계에 사용된 도구:
    Tweezers
    $4.99
    구매

    • Using precision tweezers, disconnect the following three bundles of wires:

    • Connecting the battery pack to the motherboard.

    • Connecting the power switch to the motherboard.

    • Connecting the speaker to the motherboard.

    편집

  10. WowWee MiP Robot LED Light Replacement, LED Light: 9 단계, 이미지 2개 중 1개 WowWee MiP Robot LED Light Replacement, LED Light: 9 단계, 이미지 2개 중 2개

    • Remove the four 7.5mm Phillips #1 screws.

    편집

  11. WowWee MiP Robot LED Light Replacement: 10 단계, 이미지 2개 중 1개 WowWee MiP Robot LED Light Replacement: 10 단계, 이미지 2개 중 2개

    • Carefully pull the motor and motherboard assembly straight out from the base.

    • Be careful not to break the plastic rods that go through the motor assembly and are connect to the shell.

    편집

  12. WowWee MiP Robot LED Light Replacement: 11 단계, 이미지 1개 중 1개
    이 단계에 사용된 도구:
    Tweezers
    $4.99
    구매

    • Use the precision tweezers to unplug the bundle of wires.

    편집

  13. WowWee MiP Robot LED Light Replacement: 12 단계, 이미지 1개 중 1개

    • Slide the head back to separate it from the body.

    • The motherboard does not need to be separated from the head to replace the LED light.

    편집

  14. WowWee MiP Robot LED Light Replacement: 13 단계, 이미지 1개 중 1개

    • Remove the 7.5mm Phillips #1 screw.

    • The LED light is soldered to the small circuit board.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

4다른 기여자 명과 함께

Courtney

회원 가입일: 02/04/16

236 평판

안내서 1개를 작성함

배지: 9

배지 +6개 더

팀

USF Tampa, Team 3-4, Wollert Spring 2016 USF Tampa, Team 3-4, Wollert Spring 2016 회원

USFT-WOLLERT-S16S3G4

4 회원들

안내서 10개를 작성함

0가이드 댓글

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 8

전체 시간: 777