소개

Use this guide to replace the bottom panel of your controller that you cracked by throwing it at the TV.

부품

부품은 필요하지 않습니다.

  1. Depress the battery release button on the top of the controller. Remove the battery holder from the controller.
    • Depress the battery release button on the top of the controller.

    • Remove the battery holder from the controller.

    • The standard option for Xbox 360 Wireless Controllers Battery Packs is AA batteries. A rechargeable battery is also available, but both battery options are removed from the controller in the same way.

  2. Use a pair of tweezers to peel the barcode sticker from the battery compartment.
    • Use a pair of tweezers to peel the barcode sticker from the battery compartment.

  3. Remove the seven 9.3 mm  T8 Security Torx screws securing the rear case to the front case.
    • Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.

    • Insert a Spudger between the front and rear cases along the left edge of the controller.

    • Rotate the spudger toward the front of the controller, prying the two cases apart.

  4. Insert a spudger between the front and rear cases, near the headphone jack. Rotate the spudger toward the front of the controller to pry the two cases apart.
    • Insert a spudger between the front and rear cases, near the headphone jack.

    • Rotate the spudger toward the front of the controller to pry the two cases apart.

  5. Grasp the controller by the battery compartment and the headphone jack. Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.
    • Grasp the controller by the battery compartment and the headphone jack.

    • Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.

    • The battery contact springs are held in place by slots in the battery housing in the rear case. Be sure to realign them properly during reassembly.

  6. US$100.00 이상 또는 Pro Tech Toolkit을 포함한 모든 주문의 배송은 무료입니다!

    상점 둘러보기
  7. Use the flat end of a spudger to remove the vibration motor cable, moving it upward from its socket on the logic board. Lift the vibration motor out of the front case.
    • Use the flat end of a spudger to remove the vibration motor cable, moving it upward from its socket on the logic board.

    • Lift the vibration motor out of the front case.

  8. Remove the vibration motor from the other side of the controller using the same method previously described. The right motor has significantly more counterweight than the left motor.
    • Remove the vibration motor from the other side of the controller using the same method previously described.

    • The right motor has significantly more counterweight than the left motor.

  9. Lifting from the headphone jack and power plug, remove the logic board from the front case. Lifting from the headphone jack and power plug, remove the logic board from the front case.
    • Lifting from the headphone jack and power plug, remove the logic board from the front case.

  10. Lift the bumper panel off of the front case. Lift the bumper panel off of the front case.
    • Lift the bumper panel off of the front case.

  11. Remove the rubber pad from the back of the D-pad.
    • Remove the rubber pad from the back of the D-pad.

  12. Remove the two 7.0 mm silver Phillips screws from the back of the D-pad.
    • Remove the two 7.0 mm silver Phillips screws from the back of the D-pad.

  13. The D-pad is secured to its backing by two diagonal clips, shown in red. Use a pair of tweezers and squeeze the clips together to release the D-pad from its backing.
    • The D-pad is secured to its backing by two diagonal clips, shown in red.

    • Use a pair of tweezers and squeeze the clips together to release the D-pad from its backing.

  14. Lift the D-pad backing out of its compartment on the front case. The D-pad remains below the front case.
    • Lift the D-pad backing out of its compartment on the front case.

    • The D-pad remains below the front case.

    • The D-pad will fall once its backing is removed. Be sure to support it as you remove the backing.

    • The backing is slotted to its compartment to ensure that it will always be aligned properly.

  15. Remove the rubber pad from the back of the input buttons.
    • Remove the rubber pad from the back of the input buttons.

  16. Using a pair or tweezers, remove the following buttons from the front panel: A Button
    • Using a pair or tweezers, remove the following buttons from the front panel:

      • A Button

      • B Button

      • X Button

      • Y Button

      • Start Button

      • Select Button

      • Guide Button

  17. Using a pair of tweezers, remove the LED ring from the front panel.
    • Using a pair of tweezers, remove the LED ring from the front panel.

  18. Insert a spudger between the lower panel and front case. Slide the spudger along the gap between the two case components. Lift the lower panel off of the front case.
    • Insert a spudger between the lower panel and front case.

    • Slide the spudger along the gap between the two case components.

    • Lift the lower panel off of the front case.

결론

To reassemble your device, follow these instructions in reverse order.

다른 13명이 해당 안내서를 완성하였습니다.

Brett Hartt

회원 가입일: 2010년 04월 12일

109,780 평판

안내서 138개 작성하였습니다

iFixit iFixit 회원

Community

109 회원들

안내서 7,717개 작성하였습니다

I have 2 remote controllers of X box one which is not working.

ravi.gopalakrishnan - 답글

조회 통계:

지난 24시간: 2

지난 7일: 14

지난 30일: 50

전체 시간: 14,302