메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Xbox 360 Wireless Controller Rear Case Replacement

작성자 Brett Hartt (또 다른 기여자 6명)
  • 댓글 5
  • 즐겨찾기 24
  • 완료: 20

난이도

보통

단계

6

소요 시간

시간 제안??

섹션

2

플래그

0

소개

Stop holding your Xbox 360 wireless controller together with duct tape. Use this guide to replace your old broken rear case.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Depress the battery release button on the top of the controller. Remove the battery holder from the controller.

    • Depress the battery release button on the top of the controller.

    • Remove the battery holder from the controller.

    • The standard option for Xbox 360 Wireless Controllers Battery Packs is AA batteries. A rechargeable battery is also available, but both battery options are removed from the controller in the same way.

    편집

  2. Use a pair of tweezers to peel the barcode sticker from the battery compartment.

    • Use a pair of tweezers to peel the barcode sticker from the battery compartment.

    편집

  3. 안드로이드 수리 키트

    A new screen or battery is one kit away.

    지금 장보기

    안드로이드 수리 키트

    A new screen or battery is one kit away.

    지금 장보기

  4. Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.

    • Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.

    편집

  5. Insert a Spudger between the front and rear cases along the left edge of the controller. Rotate the spudger toward the front of the controller, prying the two cases apart.
    이 단계에 사용된 도구:
    Spudger
    $2.99

    • Insert a Spudger between the front and rear cases along the left edge of the controller.

    • Rotate the spudger toward the front of the controller, prying the two cases apart.

    편집

  6. Insert a spudger between the front and rear cases, near the headphone jack. Rotate the spudger toward the front of the controller to pry the two cases apart.

    • Insert a spudger between the front and rear cases, near the headphone jack.

    • Rotate the spudger toward the front of the controller to pry the two cases apart.

    편집

  7. Grasp the controller by the battery compartment and the headphone jack. Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.

    • Grasp the controller by the battery compartment and the headphone jack.

    • Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.

    • The battery contact springs are held in place by slots in the battery housing in the rear case. Be sure to realign them properly during reassembly.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 20명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 6명과 함께

Brett Hartt

회원 가입일: 2010년 04월 12일

113,744 평판

안내서 143개 작성하였습니다

배지: 50

배지 +47개 더

팀

iFixit iFixit 회원

Community

106 회원들

안내서 9,288개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 10

지난 30일: 35

전체 시간: 18,646