물건을 수리하세요 커뮤니티 상점

Xbox 360 Wireless Controller Rear Case Replacement

소개

Stop holding your Xbox 360 wireless controller together with duct tape. Use this guide to replace your old broken rear case.

필요한 것

  1. Xbox 360 Wireless Controller Rear Case Replacement, Battery: 1 단계, 이미지 2개 중 1개 Xbox 360 Wireless Controller Rear Case Replacement, Battery: 1 단계, 이미지 2개 중 2개

    • Depress the battery release button on the top of the controller.

    • Remove the battery holder from the controller.

    • The standard option for Xbox 360 Wireless Controllers Battery Packs is AA batteries. A rechargeable battery is also available, but both battery options are removed from the controller in the same way.

    편집

  2. Xbox 360 Wireless Controller Rear Case Replacement, Rear Case: 2 단계, 이미지 1개 중 1개
    이 단계에 사용된 도구:
    Tweezers
    $4.99
    구매

    • Use a pair of tweezers to peel the barcode sticker from the battery compartment.

    편집

  4. Xbox 360 Wireless Controller Rear Case Replacement: 3 단계, 이미지 1개 중 1개

    • Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.

    편집

  5. Xbox 360 Wireless Controller Rear Case Replacement: 4 단계, 이미지 2개 중 1개 Xbox 360 Wireless Controller Rear Case Replacement: 4 단계, 이미지 2개 중 2개
    이 단계에 사용된 도구:
    Spudger
    $2.99
    구매

    • Insert a Spudger between the front and rear cases along the left edge of the controller.

    • Rotate the spudger toward the front of the controller, prying the two cases apart.

    편집

  6. Xbox 360 Wireless Controller Rear Case Replacement: 5 단계, 이미지 2개 중 1개 Xbox 360 Wireless Controller Rear Case Replacement: 5 단계, 이미지 2개 중 2개

    • Insert a spudger between the front and rear cases, near the headphone jack.

    • Rotate the spudger toward the front of the controller to pry the two cases apart.

    편집

  7. Xbox 360 Wireless Controller Rear Case Replacement: 6 단계, 이미지 2개 중 1개 Xbox 360 Wireless Controller Rear Case Replacement: 6 단계, 이미지 2개 중 2개

    • Grasp the controller by the battery compartment and the headphone jack.

    • Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.

    • The battery contact springs are held in place by slots in the battery housing in the rear case. Be sure to realign them properly during reassembly.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 24명이 해당 안내서를 완성하였습니다.

작성자

6다른 기여자 명과 함께

Brett Hartt

회원 가입일: 04/12/10

129,821 평판

안내서 143개를 작성함

배지: 52

배지 +49개 더

팀

iFixit iFixit 회원

Staff

118 회원들

안내서 19,418개를 작성함

댓글 0개

댓글 쓰기

조회 통계:

지난 24시간: 5

지난 7일: 15

지난 30일: 59

전체 시간: 23,922