메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Xbox One S Interior Case Top Panel Replacement

작성자 Andrew (및 기여자 1명)
  • 댓글 1
  • 즐겨찾기 0
  • 완료: 1

난이도

쉬움

단계

8

소요 시간

30 초

섹션

2

플래그

0

소개

This guide will show you how to remove the top panel of the interior case of the Xbox Box One S. This is necessary for the removal of either the hard drive, the disk drive, the heatsink/fan, the motherboard, or the power block.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Flip the Xbox One S so that the bottom of the case is facing upward.

    • Flip the Xbox One S so that the bottom of the case is facing upward.

    편집

  2. Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place.

    • Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place.

    • Use the opening tool to pop the clips out. The best method is to pry the black case away from the bottom.

    • You will hear clicking sounds when you are prying the case open. It may be fairly difficult to remove the bottom.

    • It's possible that the clips may break when you remove the bottom from the case.

    • We recommend starting at one corner and sliding the prying tool along the edges of the Xbox One S. Once the first few clips are opened you can lift the cover up to find the remaining clips.

    편집

  3. Once all of the clips are opened, remove the bottom part of the case.

    • Once all of the clips are opened, remove the bottom part of the case.

    편집

  4. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

  5. Find all of the green screws on the metal case labeled F1 through F6. Take the T10 Torx screwdriver and remove the six 50 mm long screws.

    • Find all of the green screws on the metal case labeled F1 through F6.

    • Take the T10 Torx screwdriver and remove the six 50 mm long screws.

    편집

  6. The port cover is held in place with rivets. Insert a pry tool gently between the top cover and metal casing on both sides to prepare the cover for removal. The port cover is held in place with rivets. Insert a pry tool gently between the top cover and metal casing on both sides to prepare the cover for removal. The port cover is held in place with rivets. Insert a pry tool gently between the top cover and metal casing on both sides to prepare the cover for removal.

    • The port cover is held in place with rivets. Insert a pry tool gently between the top cover and metal casing on both sides to prepare the cover for removal.

    편집

  7. Gently separate the interior case from the white exterior case using the appropriate method. Gently separate the interior case from the white exterior case using the appropriate method.

    • Gently separate the interior case from the white exterior case using the appropriate method.

    편집

  8. Flip the interior case so it is fan side upward.

    • Flip the interior case so it is fan side upward.

    편집

  9. Gently pop and lift the metal panel on top of the interior case to access the hardware. It should come right off.

    • Gently pop and lift the metal panel on top of the interior case to access the hardware. It should come right off.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 1명과 함께

Andrew

회원 가입일: 2017년 04월 26일

1,640 평판

안내서 3개 작성하였습니다

배지: 13

배지 +10개 더

팀

Cal Poly, Team S22-G3, Livingston Spring 2017 Cal Poly, Team S22-G3, Livingston Spring 2017 회원

CPSU-LIVINGSTON-S17S22G3

4 회원들

안내서 33개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 4

지난 30일: 30

전체 시간: 844