메인 콘텐츠로 스킵하기

소개

This guide will show you how to remove the back panel of the device. You will need a plastic opening tool, tweezers, and a #00 Phillips screwdriver in order to remove the back panel of the phone.

  1. Flip the phone over so that the back panel of the phone is facing up.
    • Flip the phone over so that the back panel of the phone is facing up.

    • Wedge the plastic opening tool between the black outer panel and the silver side panel.

    • Push down on the plastic opening tool to separate the back panel from the rest of the phone.

    • Continue to do this around all sides of the phone until the back panel has popped all the way off.

    • Removing the back panel may make loud popping noises which is normal.

  2. Using your fingers, slide the SIM card all the way out of the phone.
    • Using your fingers, slide the SIM card all the way out of the phone.

  3. Remove the yellow Kapton tape by using the tweezers to peel it up and away from the device. Remove the yellow Kapton tape by using the tweezers to peel it up and away from the device.
    • Remove the yellow Kapton tape by using the tweezers to peel it up and away from the device.

  4. 아이폰 배터리 수리 키트

    Only $29.99

    Buy Now

    아이폰 배터리 수리 키트

    Only $29.99

    Buy Now
  5. Using the Phillips #00 screwdriver, remove the two 3.0 mm screws located near the top of the phone, next to the rear camera.
    • Using the Phillips #00 screwdriver, remove the two 3.0 mm screws located near the top of the phone, next to the rear camera.

  6. Remove the  fingerprint sensor flex cable, using the plastic opening tool to lift it out.
    • Remove the fingerprint sensor flex cable, using the plastic opening tool to lift it out.

  7. Using the tweezers, peel back the yellow Kapton tape located on the right side of the phone. Using the tweezers, peel back the yellow Kapton tape located on the right side of the phone.
    • Using the tweezers, peel back the yellow Kapton tape located on the right side of the phone.

  8. Using the Phillips #00 screwdriver, remove the 15,  3.0 mm rear panel screws located around the perimeter of the phone.
    • Using the Phillips #00 screwdriver, remove the 15, 3.0 mm rear panel screws located around the perimeter of the phone.

  9. Flip the phone over so that the screen is facing up.
    • Flip the phone over so that the screen is facing up.

    • Wedge the plastic opening tool between the screen and the rear panel.

    • Push up on the opening tool to separate the panel from the phone.

    • Continue to do this around the entire phone until the rear panel is no longer connected to the device.

    • The rear case and screen are fastened tightly to each other. It might help to use the picks as wedges to keep the case and screen separated as you run the opening tool along the edges.

결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

Mihir Deshmukh

회원 가입일: 2018년 04월 18일

327 평판

안내서 1개 작성함

Cal Poly, Team S17-G3, Livingston Spring 2018 Cal Poly, Team S17-G3, Livingston Spring 2018 회원

CPSU-LIVINGSTON-S18S17G3

4 회원들

안내서 8개 작성하였습니다

When I tried this at step 8 the screen peeled off instead of the top cover. Ruined my phone.

Solomon Martinez - 답글

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 3

지난 30일: 20

전체 시간: 432