이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
-
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Push the wire clasp away from the AirPort card and toward the display, then rotate up to free it from the RAM shield.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Grasp the clear plastic tab on the AirPort card and pull toward the display.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Hold the AirPort card in one hand and use your other hand to remove the antenna cable.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Grasp the metal bracket on top of the RAM shield and pull upward to remove the shield.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a pin (or anything you like) to remove the three rubber feet from the lower case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the three hex screws using a T8 Torx screwdriver (or Allen screws using an Allen key if these are used).
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Push the thin rims of the lower case surrounding the battery compartment in, bending them past the tabs, and then lift up to free that corner of the lower case.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free (it may be helpful to jiggle the case up and down).
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 10 screws from the bottom shield:
-
Six 3 mm Phillips
-
Three 7.5 mm Phillips
-
One 14 mm Phillips
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Deroute the cable from around the optical drive, removing tape as necessary, and angle the DC-In board out of its compartment.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 11 screws from the bottom of the computer:
-
Three 3 mm Phillips around the battery compartment. (Some models may only have two screws.)
-
Three 4.5 mm Phillips along the optical drive bezel. (a magnetic screwdriver may help to lift these screws out)
-
One 11 mm Phillips in the lower right corner. (if present)
-
Four 14.5 mm Phillips.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Turn over the computer and open it.
-
Remove the 2 Phillips screws (3mm) from the edges of the keyboard area.
-
Remove the 4 mm Phillips screw from the lower left corner.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the upper case and use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab. Due to model variatons your trackpad connector may be different than the one pictured.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Carefully lift the upper case about half of an inch and move it so that you can access the power and speaker cables.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board. Using your fingernails or a dental pick, carefully pry the connector from its socket. Make sure you're pulling only on the connector and not on the socket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Carefully disconnect the multicolored speaker cable from the logic board. As before, make sure you're pulling only on the connector and not on the socket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 16 screws:
-
Thirteen 3 mm Phillips.
-
One 3 mm Phillips. (actual screw not present in image)
-
Two 4 mm Phillips.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the top shield up from the right side, minding the upper left corner, which may catch on the metal framework.
-
If your iBook has Bluetooth, as discussed in the previous step, you will need to slide the antenna through the lower I-shaped hole in the shield before completely removing the shield.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Turn the computer over.
-
Disconnect the inverter cable from the logic board and deroute it from the metal framework, removing tape as necessary.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Turn the computer back over.
-
Disconnect the microphone cable at the front of the computer, between the left side of the hard drive and the metal framework.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the black plastic loop to disconnect the display data cable from the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Deroute the microphone and display data cables from the metal framework, removing tape as necessary.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Deroute the AirPort antenna cable from the metal framework, removing tape as necessary.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Support the display with one hand and remove the single Phillips screw on either side of the hinge (two screws total).
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the display up and tilt it backwards, freeing it from the two metal alignment posts holding the hinges in place, and slide it away from you.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two Phillips screws securing the hinge grill to the metal framework.
-
Lift the hinge grill out of the computer.
-
다른 한 분이 해당 안내서를 완성하였습니다.