기기를 수리하세요 커뮤니티 상점

iDea USA CT702 Battery Replacement

소개

This simple task of replacing the battery will lengthen the lifespan of the charge on the iDeaUSA CT702.

필요한 것

  1. iDea USA CT702 Battery Replacement, Battery: 1 단계, 이미지 1/1

    • Face the tablet with portholes facing you.

    번역하기

  2. iDea USA CT702 Battery Replacement: 2 단계, 이미지 1/1

    • Use a fingernail or a plastic opening tool to gently pry the black panel around the portholes.

    • Be gentle and take your time.

    번역하기

  3. iDea USA CT702 Battery Replacement: 3 단계, 이미지 1/3 iDea USA CT702 Battery Replacement: 3 단계, 이미지 2/3 iDea USA CT702 Battery Replacement: 3 단계, 이미지 3/3

    • Use your fingers to remove the rest of the back. Slowly apply pressure from each side to detach each clip connection.

    번역하기

  4. iDea USA CT702 Battery Replacement: 4 단계, 이미지 1/2 iDea USA CT702 Battery Replacement: 4 단계, 이미지 2/2

    • Separate the battery from the device.

    • Slowly use your thumb and forefingers to pry open each corner.

    • Be aware of the adhesive on the bottom of the battery. Remove with care to keep battery intact.

    번역하기

  6. iDea USA CT702 Battery Replacement: 5 단계, 이미지 1/1

    • Carefully peel off tape around the top of the battery.

    • Slowly use your fingernail to lift the tape off of the battery. Dispose of the tape or save it for reuse.

    번역하기

  7. iDea USA CT702 Battery Replacement: 6 단계, 이미지 1/3 iDea USA CT702 Battery Replacement: 6 단계, 이미지 2/3 iDea USA CT702 Battery Replacement: 6 단계, 이미지 3/3

    • Disconnect the battery using the soldering iron.

    • Remember to use proper safety precautions when soldering. Solder from the side and do not breathe the smoke in.

    • Make sure the soldering iron is on the highest heat for 5 minutes before starting.

    • Start with the red wire, and gently touch the tip of the iron onto the connection.

    • Move to the yellow wire after the red.

    • Move to the black wire after the yellow.

    번역하기

  8. iDea USA CT702 Battery Replacement: 7 단계, 이미지 1/1

    • Remove the battery completely. Dispose of the defective battery properly at a recycling center.

    번역하기

  9. iDea USA CT702 Battery Replacement: 8 단계, 이미지 1/1

    • Put the new battery in place

    • Make sure the corners are inside of the white shell.

    번역하기

  10. iDea USA CT702 Battery Replacement: 9 단계, 이미지 1/2 iDea USA CT702 Battery Replacement: 9 단계, 이미지 2/2

    • Solder the new battery.

    • Start with the black wire and solder to the nearest connection.

    • Move to the yellow wire and solder to the middle connection.

    • End with the red wire and solder to the farthest connection away.

    번역하기

  11. iDea USA CT702 Battery Replacement: 10 단계, 이미지 1/2 iDea USA CT702 Battery Replacement: 10 단계, 이미지 2/2

    • Re-tape the battery at the top.

    • Make sure the solder has cooled before taping.

    • Tape the corners in place, onto the shell.

    • To replace back cover, follow the first three steps in reverse order.

    번역하기
결론

To reassemble your device, Start from step 9 and work backwards.

작성자

다른 기여자 7명과 함께

Benton Gray

회원 가입일: 03/11/15

201 평판

안내서 2개 작성하였습니다

배지: 3

팀

Colorado Springs, Team 4-7, Panko Spring 2015 Colorado Springs, Team 4-7, Panko Spring 2015 회원

UCCS-PANKO-S15S4G7

3 회원들

안내서 10개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 2

7일 전: 2

30일 전: 3

전체 시간: 604