주요 콘텐츠로 건너뛰기

필요한 것

  1. iPad 3 Wi-Fi Headphone Jack Assembly Replacement, Headphone Jack Assembly: 1 단계, 이미지 1/2 iPad 3 Wi-Fi Headphone Jack Assembly Replacement, Headphone Jack Assembly: 1 단계, 이미지 2/2
    • Peel back and remove the adhesive tape covering the headphone jack assembly.

  2. iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 2 단계, 이미지 1/3 iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 2 단계, 이미지 2/3 iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 2 단계, 이미지 3/3
    • Using the flat end of a spudger, pry the front-facing camera connector off of its socket on the headphone jack assembly.

    • Slide the spudger to the right, releasing the adhesive holding down the camera cable.

  3. iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 3 단계, 이미지 1/2 iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 3 단계, 이미지 2/2
    • Using the tip of a spudger, flip up the retaining flap on the microphone cable ZIF connector.

  4. iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 4 단계, 이미지 1/2 iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 4 단계, 이미지 2/2
    • Insert the tip of the spudger underneath the microphone ribbon cable, removing it from its ZIF connector.

    • Slide the spudger to the left, releasing the adhesive holding the microphone ribbon cable to the headphone jack assembly.

  5. iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 5 단계, 이미지 1/2 iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 5 단계, 이미지 2/2
    • Flip up the retaining flap securing the volume/power button ribbon cable connector to the headphone jack assembly board.

    • Remove the volume button ribbon cable from its ZIF connector.

  6. iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 6 단계, 이미지 1/3 iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 6 단계, 이미지 2/3 iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 6 단계, 이미지 3/3
    • Remove the following screws from the headphone jack assembly:

    • Five 2.6 mm Phillips #0

    • Two 2.0 mm Wide Head Phillips #00

    • Two 2.6 mm Phillips #00

    • These screws are angled into the aluminum frame. Be sure to hold the screwdriver so that the screwdriver is in line with the screw, to avoid stripping the screw.

  7. iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 7 단계, 이미지 1/2 iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 7 단계, 이미지 2/2
    • Gently peel the headphone jack assembly ribbon cable up from the foam pad in the top left of the rear case.

    • If necessary, use the flat end of a spudger to loosen the adhesive securing the ribbon cable to the foam.

  8. iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 8 단계, 이미지 1/2 iPad 3 Wi-Fi Headphone Jack Assembly Replacement: 8 단계, 이미지 2/2
    • Grasping the headphone jack assembly with both hands, pull the assembly from the iPad, minding any cables that may get caught.

결론

To reassemble your device, follow these instructions in reverse order.

Walter Galan

682,478 평판

안내서 1,203개 작성하였습니다

0 Comments

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 83