메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

iPad 4 Wi-Fi Headphone Jack Assembly Replacement

작성자 Walter Galan
  • 댓글 1
  • 즐겨찾기 0

난이도

보통

단계

9

소요 시간

시간 제안??

섹션

1

플래그

1

Prerequisite Only

단지 전제 조건

해당 안내서는 단지 다른 안내서의 전제 조건임을 참고하시기 바랍니다.

소개

Internal prereq.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Carefully move, but do not remove the front-facing camera ribbon cable aside with the flat edge of a spudger.

    • Carefully move, but do not remove the front-facing camera ribbon cable aside with the flat edge of a spudger.

    편집

  2. Peel back and remove the adhesive tape covering the headphone jack assembly. Peel back and remove the adhesive tape covering the headphone jack assembly.

    • Peel back and remove the adhesive tape covering the headphone jack assembly.

    편집

  3. Using the tip of the spudger, flip up the retaining flap on the microphone cable ZIF connector.

    • Using the tip of the spudger, flip up the retaining flap on the microphone cable ZIF connector.

    편집

  4. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

  5. Insert the tip of the spudger underneath the microphone ribbon cable and carefully push it out from its socket on the ZIF connector. Use the flat edge of a spudger to move the microphone ribbon cable aside.

    • Insert the tip of the spudger underneath the microphone ribbon cable and carefully push it out from its socket on the ZIF connector.

    • Use the flat edge of a spudger to move the microphone ribbon cable aside.

    편집

  6. Flip up the retaining flap securing the volume/power button ribbon cable connector to the headphone jack assembly board.

    • Flip up the retaining flap securing the volume/power button ribbon cable connector to the headphone jack assembly board.

    편집

  7. Push the volume button ribbon cable from its ZIF connector. Gently bend the volume button ribbon cable upwards to move it aside.

    • Push the volume button ribbon cable from its ZIF connector.

    • Gently bend the volume button ribbon cable upwards to move it aside.

    편집

  8. Remove the following screws from the headphone jack assembly: Five 2.6 mm Phillips #0 Two 2.2 mm Wide Head Phillips #00

    • Remove the following screws from the headphone jack assembly:

    • Five 2.6 mm Phillips #0

    • Two 2.2 mm Wide Head Phillips #00

    • Two 2.6 mm Phillips #00

    • These screws are angled into the aluminum frame. Be sure to hold the screwdriver so that the screwdriver is in line with the screw, to avoid stripping the screw.

    편집

  9. Holding onto the ribbon cable of the headphone jack assembly, carefully pull the assembly upwards towards the top of the device.

    • Holding onto the ribbon cable of the headphone jack assembly, carefully pull the assembly upwards towards the top of the device.

    편집

  10. Grasping the headphone jack assembly with one hand, pull the assembly from the iPad, minding any cables that may get caught. Grasping the headphone jack assembly with one hand, pull the assembly from the iPad, minding any cables that may get caught.

    • Grasping the headphone jack assembly with one hand, pull the assembly from the iPad, minding any cables that may get caught.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

Walter Galan

598,030 평판

안내서 1,203개 작성하였습니다

배지: 53

배지 +50개 더

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 0

전체 시간: 15