기기를 수리하세요

수리할 권리

상점

iPad 6 Wi-Fi Front Panel Assembly Replacement

작성자 Sam Goldheart (및 기여자 1명)
  • 댓글 2
  • 즐겨찾기 0
  • 완료: 1

난이도

어려움

단계

5

소요 시간

1 - 2 시간

섹션

1

플래그

1

Prerequisite Only

단지 전제 조건

해당 안내서는 단지 다른 안내서의 전제 조건임을 참고하시기 바랍니다.

소개

This is a prerequisite only guide for the front panel replacement.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Remove any tape covering the home button ribbon cable connector. Remove any tape covering the home button ribbon cable connector.

    • Remove any tape covering the home button ribbon cable connector.

    편집

  2. Use the flat end of a spudger to flip the tab on the home button ribbon cable ZIF connector upward. Carefully pull the home button ribbon cable straight out of the ZIF connector. Carefully pull the home button ribbon cable straight out of the ZIF connector.

    • Use the flat end of a spudger to flip the tab on the home button ribbon cable ZIF connector upward.

    • Carefully pull the home button ribbon cable straight out of the ZIF connector.

    편집

  4. Use a the flat end of a spudger or a fingernail to carefully pop the two digitizer cable connectors straight up from their sockets. To avoid damaging your iPad, pry only on the connectors themselves, not on the socket on the logic board. During reassembly, make sure that these connectors are completely seated in their sockets, or you may encounter display issues.

    • Use a the flat end of a spudger or a fingernail to carefully pop the two digitizer cable connectors straight up from their sockets.

    • To avoid damaging your iPad, pry only on the connectors themselves, not on the socket on the logic board.

    • During reassembly, make sure that these connectors are completely seated in their sockets, or you may encounter display issues.

    편집

  5. Carefully peel the home button ribbon cable up off of the adhesive holding it to the rear case. Carefully peel the home button ribbon cable up off of the adhesive holding it to the rear case.

    • Carefully peel the home button ribbon cable up off of the adhesive holding it to the rear case.

    편집

  6. Remove the front panel assembly. If you experience "ghost" or "phantom" touch input issues with your new display, this can be resolved by adding a layer of very thin insulating tape, such as Kapton (polyimide) tape, to the highlighted areas on the back of the panel. iFixit panels come with the proper insulation, and should not require the addition of any tape.
    이 단계에 사용된 도구:
    Polyimide Tape
    $9.99

    • Remove the front panel assembly.

    • If you experience "ghost" or "phantom" touch input issues with your new display, this can be resolved by adding a layer of very thin insulating tape, such as Kapton (polyimide) tape, to the highlighted areas on the back of the panel. iFixit panels come with the proper insulation, and should not require the addition of any tape.

    • Without the proper insulation, these areas of the digitizer can ground out against other components, causing touch input malfunction.

    • The insulation is not visible to the naked eye, and is different from the foam dust barrier strips found on many iPads.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 1명과 함께

Sam Goldheart

회원 가입일: 2012년 10월 18일

433,551 평판

안내서 547개 작성하였습니다

배지: 48

배지 +45개 더

팀

iFixit iFixit 회원

Community

134 회원들

안내서 14,666개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 2

전체 시간: 72