이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Heat an iOpener and apply it to the left edge of the device for two minutes.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
While you're waiting for the adhesive to loosen, note the following areas that are sensitive to prying:
-
Front camera
-
Antennas
-
Display cables
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
이 단계에 사용된 도구:Anti-Clamp$24.95-
Pull the blue handle backwards to unlock the Anti-Clamp's arms.
-
Place an object under your iPad so it rests level between the suction cups.
-
Position the suction cups near the middle of the left edge—one on the top, and one on the bottom.
-
Hold the bottom of the Anti-Clamp steady and firmly press down on the top cup to apply suction.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the blue handle forward to lock the arms.
-
Turn the handle clockwise 360 degrees or until the cups start to stretch.
-
Make sure the suction cups remain aligned with each other. If they begin to slip out of alignment, loosen the suction cups slightly and realign the arms.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Wait one minute to give the adhesive a chance to release and present an opening gap.
-
If your screen isn't getting hot enough, you can use a hair dryer to heat along the left edge of the iPad.
-
Insert an opening pick under the digitizer when the Anti-Clamp creates a large enough gap.
-
Skip the next step.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Once the screen is warm to touch, apply a suction handle to the left edge of the screen and as close to the edge as possible.
-
Lift the screen with the suction handle to create a small gap between the digitizer and the frame.
-
Insert an opening pick into the gap between the digitizer and the frame.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert a second opening pick into the gap you just created.
-
Slide the pick toward the bottom-left corner of the device to separate the adhesive.
-
Leave the pick in the bottom-left corner to prevent the adhesive from re-sealing.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad to continue separating the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the first opening pick towards the top-left corner of the device to separate the adhesive.
-
Leave the pick in the top-left corner to prevent the adhesive from re-sealing.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Heat an iOpener and apply it to the top edge of the device for two minutes.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Rotate the pick around the top-left corner of the device to separate the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the opening pick along the top edge of the device, stopping just before you reach the front camera.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the pick out until only the tip is between the digitizer and the frame.
-
Slide the pick above the front camera to separate the adhesive.
-
Leave the pick near the right side of the front camera before continuing.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Re-insert the pick and slide it towards the top-right corner of the device to completely separate the top adhesive.
-
Leave the pick in the top-right corner to prevent the adhesive from re-sealing.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Heat an iOpener and apply it to the right edge of the device for two minutes.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Rotate the pick around the top-right corner of the device to separate the adhesive.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert a new opening pick and slide it to the middle of the iPad's right edge.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Heat an iOpener and apply it to the bottom edge of the device for two minutes.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the bottom-left pick to the bottom-left corner to separate the adhesive.
-
Leave the pick in the bottom-left corner before moving to the next step.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert a new opening pick into the gap you just created on the bottom edge of the iPad.
-
Slide the pick over the antenna, stopping just before the home button.
-
Leave the pick to the left of the home button before continuing.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert an opening pick into the gap you just created.
-
Slide the pick underneath the home button and towards the bottom-right corner, making sure only the tip is between the digitizer and the frame.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Re-insert the pick and slide it towards the home button to completely separate the bottom adhesive.
-
Leave the pick to the right of the home button before continuing.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Heat an iOpener and apply it to the right edge of the device for two minutes.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Twist the two opening picks on the left corners of the iPad to lift the digitizer slightly, separating the the last of the adhesive in the process.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the left edge of the digitizer upwards to further separate the adhesive along the right edge of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
While supporting the digitizer, slide an opening pick between the two display cables to separate the last of the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Once all of the adhesive has been separated, open the digitizer like a book and rest it parallel to the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to pry the LCD out of its recess just enough to grab it with your fingers. There may be glue around the screw holes that needs to be cut with a knife.
-
Flip the iPad LCD like a page in a book, lifting near the camera and turning it over the home button end of the rear case.
-
Lay the LCD on its face to allow access to the display cables.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the single 2.3 mm Phillips #000 screw securing the battery connector to the logic board.
-
Slide the battery blocker underneath the logic board's battery connector at a 35 degree angle.
-
Leave the battery blocker in place as you work.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the three 1.4 mm Phillips #000 screws from the display cable bracket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to gently pry the display cable bracket straight up from the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to flip the tab on the home button ribbon cable ZIF connector upward.
-
Carefully pull the home button ribbon cable straight out of the ZIF connector.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a the flat end of a spudger or a fingernail to carefully pop the two digitizer cable connectors straight up from their sockets.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Carefully peel the home button ribbon cable up off of the adhesive holding it to the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
이 단계에 사용된 도구:Polyimide Tape$9.99-
Remove the front panel assembly.
-
If you experience "ghost" or "phantom" touch input issues with your new display, this can be resolved by adding a layer of very thin insulating tape, such as Kapton (polyimide) tape, to the highlighted areas on the back of the panel. iFixit panels come with the proper insulation, and should not require the addition of any tape.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Gently begin peeling the home button cable off the back of the front panel.
-
Continue peeling until you reach the metal shield on the cable.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert an opening pick between the metal shield and the front panel and gently pry it from the digitizer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a plastic opening tool to pry the home button bracket off the back of the front panel.
-
Once you've separated one side of the home button bracket, firmly grasp the bracket and peel it off the front panel.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Press the home button from the external side of the digitizer to break up the adhesive holding it in place.
-
다른 179명이 해당 안내서를 완성하였습니다.
댓글 46개
does the front panel of the ipad5 fit here?
cndals0075 - 답글
The display connectors on the iPad 5 and iPad 6 are at different angles and not directly compatible with each other. We have not yet tried to force the connectors from an iPad 6 display onto an iPad 5 and vice versa to see what happened.