이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
-
냄비나 팬에 iOpener가 완전히 잠길 정도로 충분한 물을 채우세요.
-
물이 끓을 때까지 가열하세요. 불을 끄세요.
-
iOpener를 뜨거운 물에 2~3분간 담그세요. iOpener가 물에 완전히 잠겼는지 확인합니다.
-
집게를 사용하여 뜨거운 물에서 가열된 아이오페너를 꺼내세요.
-
수건으로 iOpener를 완전히 말리세요.
-
iOpener를 사용할 준비가 되었습니다! iOpener를 재가열해야 한다면 물을 끓인 후 불을 끄고 2~3분 동안 iOpener를 물에 담가 두세요.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.
-
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Handling it by the tabs on either end, place a heated iOpener over the top edge of the iPad.
-
Let the iOpener sit on the iPad for two minutes to soften the adhesive securing the front panel to the rest of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
As you follow the directions, take special care to avoid prying in the following areas:
-
Home Button
-
Front Facing Camera
-
Main Camera
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
이 단계에 사용된 도구:Anti-Clamp$24.95-
Elevate the iPad enough for the Anti-Clamp's arms to rest above and below the screen.
-
Pull the blue handle towards the hinge to disengage opening mode.
-
Position the suction cups near the top edge of the iPad—one on the front, and one on the back.
-
Push down on the cups to apply suction to the desired area.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Push the blue handle away from the hinge to engage opening mode.
-
Turn the handle clockwise until you see the cups start to stretch.
-
Wait one minute to give the adhesive a chance to release and present an opening gap.
-
Insert an opening pick under the screen when the Anti-Clamp creates a large enough gap.
-
Skip the next two steps.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Place a suction cup over the iPad's front-facing camera and press down to create a seal.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Firmly pull up on the suction cup to create a small gap between the front panel and the rear case.
-
Once you've opened a sufficient gap, insert an opening pick into the gap to prevent the adhesive from resealing.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the pick along the edge of the display, towards the headphone jack.
-
If there is still a considerable amount of resistance when sliding the opening pick, repeat the iOpener heating procedure and apply additional heat.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the second pick along the top edge of the iPad, towards the Sleep/Wake Button.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Bring the right opening pick down and around the top right corner of the iPad.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Reheat the iOpener and lay it over the right edge of the display to loosen the adhesive underneath.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the left-hand opening pick about halfway down the edge of the display.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the opposite opening pick down to the bottom right corner of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the left-hand opening pick down the edge of the display until you reach the corner.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Bring the right-hand opening pick around the bottom corner of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the left-hand opening pick along the bottom edge of the display, then remove it from the bottom right corner of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Twist the remaining pick by the front-facing camera to separate the top edge of the display assembly from the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue lifting the display assembly from the front-facing camera side.
-
Pull the display slightly away from the bottom edge to completely separate it from the rear case.
-
Keep lifting until the display assembly is roughly perpendicular to the body of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the single 1.8 mm Phillips screw securing the battery terminals to their contacts on the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide a battery isolation pick underneath the battery connector area of the logic board, and leave it in place while you work.
-
Alternatively, make a battery blocker using a playing card and slide it underneath the logic board connector to disconnect the battery.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the three 1.3mm Phillips screws from the display cable bracket.
-
Remove the bracket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Disconnect the display data connector from its socket on the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Disconnect the two remaining digitizer cables underneath the display data cable.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a plastic opening tool to pry the bracket off the back of the Home Button.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
이 단계에 사용된 도구:Tesa 61395 Tape$5.99-
Remove the Home Button bracket and peel up the tape connected to it.
-
Scrape off as much of the old adhesive residue from the bracket as you can, then clean it with acetone or high-concentration (90% or greater) isopropyl alcohol.
-
Secure the bracket with hot-melt glue, superglue, or high-strength double-sided tape. Make sure the bracket is aligned correctly before allowing your adhesive to cure, or the home button will not click when pressed.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to flip up the retaining flap on the Home Button cable socket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to peel up the Home Button ribbon cable and Touch ID control chip.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Reheat your iOpener and lay it over the bottom edge of the display to loosen the adhesive on the Home Button gasket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the pointed end of a spudger to gently pry the Home Button assembly up from the display.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue working the tip of the spudger around the edge of the gasket until the gasket is fully separated from the front panel.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Examine your replacement part, and your original display carefully to be sure they match.
-
Your replacement screen may be missing the sleep/wake sensor that is necessary for Smart Cover use. If you want to maintain functionality you will need to transfer the component.
-
Desolder the four solder pads from the lower left of the display to remove the sensor assembly cable.
-
다른 54명이 해당 안내서를 완성하였습니다.
댓글 한 개
The displays that iFixit sells, are they actually missing the sleep / wake sensor? Are the display sold OEM?