이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert a SIM card eject tool or paper clip into the hole next to the headphone jack.
-
Press down on the paper clip until the SIM card tray pops out.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert a metal spudger into the slot between the dock connector and the antenna cover. Gently pry up near the two tabs to create a small gap between the antenna cover and the silver front bezel.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert an iPod opening tool in the gap between the antenna cover and the front bezel. The wedge of the tool should be pointing towards the antenna cover. Slide the tool around the corner and up until you reach the metal backing.
-
Repeat the same procedure on the other side of the dock connector.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Grasp the antenna cover on either side and slide it up and away from the iPhone. This requires some force. If it does not come free, ensure that the antenna cover is lifted up enough to free the catches.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the three Phillips #00 screws securing the rear panel to the iPhone.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
The small square hole is the location to insert the dental pick in the next step.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Start removing the rear panel on the side with the buttons.
-
Slide the dental pick completely into the square hole. You may need to wiggle the tool and apply a good amount of force to get it to go all the way.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pry up the rear panel by pulling the dental pick counterclockwise in a quick motion. Apply force perpendicular to the plane of the display assembly. You may be afraid to go fast, but going slowly is more likely to bend the case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger to free the rear panel from the iPhone along the corner and top.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Repeat the same procedure on the other side of the iPhone. Slide the dental pick completely into the square hole. You may need to wiggle the tool and apply a good amount of force to get it to go all the way.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pry up the rear panel by pulling the dental pick clockwise in a quick motion. Apply force perpendicular to the plane of the display assembly. You may be afraid to go fast, but going slowly is more likely to bend the case.
-
The rear panel is still attached to the iPhone by the headphone jack cable, so don't entirely remove the rear panel from the iPhone just yet.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger to disconnect the headphone jack cable from the logic board.
-
다른 51명이 해당 안내서를 완성하였습니다.