주요 콘텐츠로 건너뛰기

소개

This guide is retained solely for historical purposes. Use the updated version of the guide to perform your repair. You can find the updated version of this guide here.

  1. Power off your iPhone before beginning disassembly.
    • Power off your iPhone before beginning disassembly.

    • Remove the two 3.4 mm Pentalobe screws surrounding the Lightning connector.

    • If you don't have an iSclack, use a single suction cup to lift the front panel:

    • Press a suction cup onto the screen, just above the home button.

    • Be sure the cup is pressed securely onto the screen to get a tight seal.

  2. There is a notch on the underside of the display just above the headphone jack that is the safest place to begin prying the phone open. Pull up on the suction cup to slightly separate the front panel assembly from the rear case. Take your time and apply firm, constant force. The display assembly is a much tighter fit than most devices and is held down with adhesive.
    • There is a notch on the underside of the display just above the headphone jack that is the safest place to begin prying the phone open.

    • Pull up on the suction cup to slightly separate the front panel assembly from the rear case.

    • Take your time and apply firm, constant force. The display assembly is a much tighter fit than most devices and is held down with adhesive.

    • Once a small gap has been opened, insert the flat end of a spudger above the headphone jack.

  3. Twist the spudger to open the gap more and break it free from the adhesive. Keep pulling up on the suction cup while twisting the spudger.
    • Twist the spudger to open the gap more and break it free from the adhesive.

    • Keep pulling up on the suction cup while twisting the spudger.

  4. Use the edge of a spudger to slice through the adhesive on either side of the phone. Use the edge of a spudger to slice through the adhesive on either side of the phone.
    • Use the edge of a spudger to slice through the adhesive on either side of the phone.

  5. Use the edge of a spudger to slice through the adhesive on either side of the phone. Use the edge of a spudger to slice through the adhesive on either side of the phone.
    • Use the edge of a spudger to slice through the adhesive on either side of the phone.

  6. Use the suction cup to open the display, breaking the last of the adhesive. Don't open the display more than 90 degrees, as it is still connected at the top by three cables that may break if stretched. Don't open the display more than 90 degrees, as it is still connected at the top by three cables that may break if stretched.
    • Use the suction cup to open the display, breaking the last of the adhesive.

    • Don't open the display more than 90 degrees, as it is still connected at the top by three cables that may break if stretched.

  7. Lean the display against something to keep it propped up while you're working on the phone.
    • Lean the display against something to keep it propped up while you're working on the phone.

  8. Remove the following screws from the battery connector bracket:
    • Remove the following screws from the battery connector bracket:

    • One 3.0 mm Phillips #00 screw

    • One 2.3 mm Phillips #00 screw

  9. Remove the metal battery connector bracket from the iPhone.
    • Remove the metal battery connector bracket from the iPhone.

  10. Use the flat end of a spudger to disconnect the battery connector from the logic board. Push the connector to the side to ensure it doesn't accidentally make contact and power on the phone while you're working on it. Push the connector to the side to ensure it doesn't accidentally make contact and power on the phone while you're working on it.
    • Use the flat end of a spudger to disconnect the battery connector from the logic board.

    • Push the connector to the side to ensure it doesn't accidentally make contact and power on the phone while you're working on it.

  11. While holding the front panel open at about a 90º angle, remove the following screws securing the front panel assembly cable bracket:
    • While holding the front panel open at about a 90º angle, remove the following screws securing the front panel assembly cable bracket:

    • Three 1.3 mm Phillips #00 screws

    • One 3.0 mm Phillips #00 screw

    • Don't lose track of this screw! It's very important that the one 3.0 mm screw goes in the top-right corner of the plate. Anywhere else may cause damage to the logic board.

  12. Remove the front panel assembly cable bracket from the logic board.
    • Remove the front panel assembly cable bracket from the logic board.

  13. In the next three steps, take care to pry up only on the cable connectors, and not on their sockets on the logic board. Use the flat end of a spudger to disconnect the front-facing camera and sensor cable connector. Use the flat end of a spudger to disconnect the front-facing camera and sensor cable connector.
    • In the next three steps, take care to pry up only on the cable connectors, and not on their sockets on the logic board.

    • Use the flat end of a spudger to disconnect the front-facing camera and sensor cable connector.

  14. Use the flat end of a spudger to disconnect the display data cable connector. When reassembling your phone, the display data cable may pop off its connector. This can result in white lines or a blank screen when powering your phone back on. If that happens, simply reconnect the cable and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery connector. When reassembling your phone, the display data cable may pop off its connector. This can result in white lines or a blank screen when powering your phone back on. If that happens, simply reconnect the cable and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery connector.
    • Use the flat end of a spudger to disconnect the display data cable connector.

    • When reassembling your phone, the display data cable may pop off its connector. This can result in white lines or a blank screen when powering your phone back on. If that happens, simply reconnect the cable and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery connector.

  15. Finally, use the flat end of a spudger to disconnect the digitizer cable connector. Finally, use the flat end of a spudger to disconnect the digitizer cable connector.
    • Finally, use the flat end of a spudger to disconnect the digitizer cable connector.

  16. Remove the display assembly from the rear case. Remove the display assembly from the rear case.
    • Remove the display assembly from the rear case.

결론

To reassemble your device, follow these instructions in reverse order.

다른 153명이 해당 안내서를 완성하였습니다.

Sam Goldheart

회원 가입일: 2012년 10월 18일

382,360 평판

안내서 543개 작성하였습니다

iFixit iFixit 회원

Community

101 회원들

안내서 9,066개 작성하였습니다

while technically correct, this guide is not complete in the sense that a new tech cannot follow it step-by-step to successfully complete a screen replacement. You should include the steps necessary to move the parts over from the old screen. Yes you can buy screen replacements with small parts but most repair operations don't do that as it isn't that hard to move them and much less expensive.

There are many small parts involved in moving from one screen to another. There are also a few steps that require prying a flex from the frame that is taped down. Having the additional steps in this guide that point out exactly where each small parts go and how to successfully pull the flex off without tearing it would be a huge improvement to this guide (and all the other screen replacement guides as they all have the same gap)

thanks - this is a great site and my techs use it for training every day.

Marty Morrow - 답글

The demo ends before it does what is stated in the heading (Display Replacement.) This demo is for Front Panel Assembly Replacement.

PJL500 -

As stated in the intro, this is just the full front panel assembly guide. We'll be posting more thorough screen replacement guides in the future. Stay tuned ;)

Sam Goldheart -

When will you be selling the 6S replacement screen. I only see on for the 6 and it says not compatible with the 6S.

Additionally is it possible to replace just the glass and not all the other parts?

dougross - 답글

That is what i am curious about as well!!!

just cracked the glass in the bottom left corner of my 6s Plus.

brink28 -

댓글 쓰기

조회 통계:

지난 24시간: 2

지난 7일: 22

지난 30일: 90

전체 시간: 184,346