주요 콘텐츠로 건너뛰기

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

iPhone 7 Power and Volume Control Cable Battery Replacement

단지 전제 조건
이 안내서는 다른 가이드의 선행 작업으로 사용하기 위한 것입니다. 그 자체로는 불완전합니다.

필요한 것

  1. iPhone 7 Power and Volume Control Cable Battery Replacement, Power and Volume Control Cable Battery: 1 단계, 이미지 1/2 iPhone 7 Power and Volume Control Cable Battery Replacement, Power and Volume Control Cable Battery: 1 단계, 이미지 2/2
    • Use the flat end of a spudger to disconnect the Taptic Engine connector from its socket on the logic board.

  2. iPhone 7 Power and Volume Control Cable Battery Replacement: 2 단계, 이미지 1/1
    • Remove the three 1.6 mm Phillips screws securing the Taptic Engine to the rear case.

  3. iPhone 7 Power and Volume Control Cable Battery Replacement: 3 단계, 이미지 1/2 iPhone 7 Power and Volume Control Cable Battery Replacement: 3 단계, 이미지 2/2
    • Remove the Taptic Engine.

  4. iPhone 7 Power and Volume Control Cable Battery Replacement: 4 단계, 이미지 1/3 iPhone 7 Power and Volume Control Cable Battery Replacement: 4 단계, 이미지 2/3 iPhone 7 Power and Volume Control Cable Battery Replacement: 4 단계, 이미지 3/3
    • Use a pair of tweezers with blunt tips to peel back one of the adhesive strips on the lower edge of the battery.

  5. iPhone 7 Power and Volume Control Cable Battery Replacement: 5 단계, 이미지 1/2 iPhone 7 Power and Volume Control Cable Battery Replacement: 5 단계, 이미지 2/2
    • Use a pair of tweezers with blunt tips to peel back the other adhesive strip on the lower edge of the battery.

  6. iPhone 7 Power and Volume Control Cable Battery Replacement: 6 단계, 이미지 1/3 iPhone 7 Power and Volume Control Cable Battery Replacement: 6 단계, 이미지 2/3 iPhone 7 Power and Volume Control Cable Battery Replacement: 6 단계, 이미지 3/3
    • Try to keep the strips flat and unwrinkled during this procedure; wrinkled strips will stick together and break instead of pulling out cleanly.

    • Slowly pull one battery adhesive tab away from the battery, toward the bottom of the iPhone.

    • Pull steadily, maintaining constant tension on the strip until it slips out from between the battery and the rear case. For best results, pull the strip at a 60º angle or less.

    • The strip will stretch to many times its original length. Continue pulling and re-grab the strip near the battery if necessary.

  7. iPhone 7 Power and Volume Control Cable Battery Replacement: 7 단계, 이미지 1/1
    • Repeat the previous step for the second strip.

    • Hold down the battery as you remove the second strip, or the strip may fling the battery when it separates from the case.

    • If you removed both adhesive strips successfully, skip the next step.

    • Otherwise, if either of the adhesive strips broke off underneath the battery and could not be retrieved, continue with the next step below.

  8. iPhone 7 Power and Volume Control Cable Battery Replacement: 8 단계, 이미지 1/2 iPhone 7 Power and Volume Control Cable Battery Replacement: 8 단계, 이미지 2/2
    • If you successfully removed both adhesive strips, move on to the next step. Otherwise, you will need to pry the battery from the rear case.

    • Prepare an iOpener and apply it to the back of the rear case, directly over the battery. Alternatively, you can apply heat using a heat gun or hair dryer.

    • After about a minute, remove the iOpener, flip the phone over and use a plastic card to break up any remaining adhesive behind the battery.

    • Avoid bending the battery. Damage to the battery may release dangerous chemicals, and could start a fire.

    • Do not pry under the top third of the battery, you may damage the volume button ribbon cable.

  9. iPhone 7 Power and Volume Control Cable Battery Replacement: 9 단계, 이미지 1/1
    • Remove the battery.

    • When installing the battery, refer to this guide to replace your battery's adhesive strips.

결론

To reassemble your device, follow these instructions in reverse order.

Scott Havard

회원 가입일: 06/27/16

49,564 평판

안내서 31개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 136