기기를 수리하세요 커뮤니티 상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

iPod Nano 5th Generation Click Wheel Replacement

단지 전제 조건
이 안내서는 다른 가이드의 선행 작업으로 사용하기 위한 것입니다. 그 자체로는 불완전합니다.

소개

A prerequisite for removing the logic board assembly.

필요한 것

  1. iPod Nano 5th Generation Click Wheel Replacement, Click Wheel: 1 단계, 이미지 1/2 iPod Nano 5th Generation Click Wheel Replacement, Click Wheel: 1 단계, 이미지 2/2

    • Use a heat gun to soften the adhesive underneath the plastic bezel at the bottom of the iPod.

    • Use a low heat setting and do not hold the heat gun in place for too long to avoid melting the plastic bezel.

    • Use a plastic opening tool to pry the bezel from the case of the iPod and remove it.

    번역하기

  2. iPod Nano 5th Generation Click Wheel Replacement: 2 단계, 이미지 1/3 iPod Nano 5th Generation Click Wheel Replacement: 2 단계, 이미지 2/3 iPod Nano 5th Generation Click Wheel Replacement: 2 단계, 이미지 3/3

    • Unscrew three screws from the bottom of the iPod:

    • Two 4.4 mm angled Phillips screws

    • One 5.4 mm Phillips screw.

    • These screws may not come out on their own, so be sure not to lose them when removing the retainer.

    • Use a plastic opening tool to pry the metal retainer out from the bottom of the iPod and remove it.

    번역하기

  4. iPod Nano 5th Generation Click Wheel Replacement: 3 단계, 이미지 1/2 iPod Nano 5th Generation Click Wheel Replacement: 3 단계, 이미지 2/2

    • Insert a metal spudger into the slot at the bottom of the iPod just above the dock connector.

    • Use the metal spudger to pry up the bottom edge of the click wheel.

    번역하기

  5. iPod Nano 5th Generation Click Wheel Replacement: 4 단계, 이미지 1/2 iPod Nano 5th Generation Click Wheel Replacement: 4 단계, 이미지 2/2

    • Place a guitar pick between the click wheel and the case of the Nano and remove the metal spudger.

    • Pry up the edges of the click wheel with the guitar pick until the click wheel comes free from the case.

    • Do not try to completely remove the click wheel yet, as it is still held in place by a ribbon cable.

    번역하기

  6. iPod Nano 5th Generation Click Wheel Replacement: 5 단계, 이미지 1/2 iPod Nano 5th Generation Click Wheel Replacement: 5 단계, 이미지 2/2

    • Lift the click wheel out of the way with one hand and use a plastic opening tool to pry the click wheel ribbon cable connector off its socket on the logic board.

    • Remove the click wheel.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 6명과 함께

Matthew Newsom

회원 가입일: 01/05/10

39,496 평판

안내서 67개 작성하였습니다

배지: 47

배지 +44개 더

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 1,164