물건을 수리하세요 커뮤니티 상점

Black Hole® Reisetasche mit Rollen Griff tauschen

안내서로 돌아가기
영어
독일어
7 단계
Handle Replacement on a Patagonia Black Hole® Wheeled Duffel, Reinstall the top handle bracket: 0 단계, 이미지 3개 중 1개 Handle Replacement on a Patagonia Black Hole® Wheeled Duffel, Reinstall the top handle bracket: 0 단계, 이미지 3개 중 2개 Handle Replacement on a Patagonia Black Hole® Wheeled Duffel, Reinstall the top handle bracket: 0 단계, 이미지 3개 중 3개
Reinstall the top handle bracket

  • Place the top handle bracket back into place on top of the handle housing and ensure that the screw holes of the handle bracket align with the screw posts of the handle housing.

  • Use a Phillips PH2 screwdriver to install the five screws securing the top handle bracket while holding the bracket in place.

  • Follow the sequential order noted in the third photo.

  • Gently hand‑tighten the screws to avoid stripping the screw wells.

  • Lift the handle bracket at each screw location to ensure it's securely in place.

Obere Griff-Halterung einbauen

Platziere die innere obere Griffhalterung oben auf das Griffgehäuse (siehe Abbildung 1).

Achte darauf, dass die Innenseite der oberen Griffhalterung mit dem Schraubenpfosten des Griffgehäuses übereinstimmt, damit die Schrauben richtig angebracht werden können (siehe Abbildung 2).

Verwende einen Kreuzschlitzschraubendreher #2 und drehe die Schrauben in der Reihenfolge ein, wie in Abbildung 3 dargestellt, um die Montage zu erleichtern und die Halterung in Position zu halten. Ziehe sie nicht zu fest an.

Nachdem du alle fünf Schrauben angebracht hast, überprüfe die Position der oberen Griffhalterung, indem du die Halterung an jeder Schraubenposition anhebst, um sicherzugehen, dass sie fest sitzt. Jede Schraube, die nicht richtig sitzt, sollte erneut angebracht werden, bis sie fest sitzt.

-[title] Reinstall Inside Top Handle Bracket
-[* black] Place Inside Top Handle Bracket on top of Handle Housing. See Reference image #1
-[* black] Ensure Inside Top Handle Bracket aligns with screw post of Handle Housing for proper installation of screws. See Reference image #2
-[* black] Using a #2 Philips Screwdriver, install screws in sequential order as pictured in Reference Image#3 for ease of installation while holding bracket in place. Do not over tighten.
-[* icon_note] After installing all 5 screws, check installation of Top Handle Bracket to ensure it's securely in place by lifting bracket up at each screw location. Any screw not properly in place should be reinstalled until firmly secure.
+[title] Reinstall the top handle bracket
+[* black] Place the top handle bracket back into place on top of the handle housing and ensure that the screw holes of the handle bracket align with the screw posts of the handle housing.
+[* yellow] Use a Phillips PH2 screwdriver to install the five screws securing the top handle bracket while holding the bracket in place.
+ [* icon_note] Follow the sequential order noted in the third photo.
+ [* icon_caution] Gently hand‑tighten the screws to avoid stripping the screw wells.
+[* black] Lift the handle bracket at each screw location to ensure it's securely in place.

귀하의 기여는 오픈 소스 Createive Commons 라이선스 하에 허가되었습니다.