동영상 개요

소개

Here is a video teardown of the ThinkPad T410s.

Below is a step by step teardown

해당 분해도는 수리 안내서가 아닙니다. Lenovo ThinkPad 410s 수리는 저희 서비스 설명서를 사용하십시오.

    • Unlatch and remove battery

    댓글 쓰기

    • Open Acess panel

    댓글 쓰기

    • Remove Hard drive

    댓글 쓰기

    • Remove wirless WAN

    댓글 쓰기

  1. Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    • Remove DIMM from back

    댓글 쓰기

    • Remove Keyboard retaing Screw from bottom of system

    • Turn the system over and open the cover. Push the keyboard toward the back and lift it up. Slide it forward to rest it on the palm rest. Disconnect the ribbon cable.

    댓글 쓰기

    • Remove BIOS battery

    댓글 쓰기

    • Disconnect the two antenna leads from the Wireless WAN card. Remove the two retaining screws. Rotate the card up and pull it out of the slot.

    • Remeber which lead goes where Prior to removing it . Grey is usually MAIN , black AUX

    댓글 쓰기

    • Remove 14 retaining screws from back

    • The first 9 are required for bezel and touchpad removal .

    • M2 × 14 mm, wafer-head, nylon-coated (6)

    • M2 × 3 mm, wafer-head, nylon-coated (3)

    • The remaining need to be removed for base cover removal

    • M2 × 5 mm, wafer-head, nylon-coated (4)

    • M2 × 10 mm, wafer-head, nylon-coated (1)

    • Note: The FPC cable is attached on the underside of the keyboard bezel assembly. In some models, the Bluetooth daughter card is also attached on the underside of the keyboard bezel assembly.

    댓글 쓰기

    • Turn system over , open , remove 4 retaining screws and the work form one side , using spudger to remove chasis bezel

    • M2 × 3 mm, wafer-head, nylon-coated (4)

    댓글 쓰기

    • Remove 4 retaining screws

    • M2 × 3 mm, wafer-head, nylon-coated (4)

    댓글 쓰기

    • Remove the two retaining screws on the bottom of the system.

    • M2.5 × 6 mm, wafer-head, nylon-coated (2)

    • Turn the system over and open the cover.

    • Unroute all the wires.

    • Remove the retaining screws.

    • M2.5 × 6 mm, wafer-head, nylon-coated (2)

    • Carefully lift the LCD panel up and out of the chass

    댓글 쓰기

kevinleroy

회원 가입일: 2012년 08월 13일

326 평판

안내서 1개 작성함

Master Techs Master Techs 회원

Community

279 회원들

안내서 758개 작성하였습니다

Uhm, sorry, what about the photos? I don't see any...

JoeMuc2014 - 답글

Still not seeing any photos accompanying the steps listed in the teardown.

Jason Landers - 답글

well. if get short out inside of USB or network line>> that has been stopping the software lunched.

mohammed - 답글

we need teardown of T410

mohammed - 답글

The video shows a teardown of the T410s. It is a lot different from the T410.

Robert Oschmann - 답글

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 10

지난 30일: 51

전체 시간: 6,654