주요 콘텐츠로 건너뛰기

기기를 고치세요

수리할 권리

부품 & 도구

동영상 개요

  1. Remove back cover. Moto G3 plastic panel can be easily removed with the fingernails.
    • Remove back cover.

    • Moto G3 plastic panel can be easily removed with the fingernails.

  2. Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath. Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath.
    • Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath.

  3. Undo 3 screws by T4 Torx screwdriver. Take away plastic securing part.
    • Undo 3 screws by T4 Torx screwdriver.

    • Take away plastic securing part.

  4. Heat up the LCD screen for a while. Then with the help of suction cup, insert guitar picks to open a gap. Slide guitar picks or plastic opening tool to cut strong adhesives. There is LCD screen connector on the left side, so be careful to slide guitar picks.
    • Heat up the LCD screen for a while.

    • Then with the help of suction cup, insert guitar picks to open a gap. Slide guitar picks or plastic opening tool to cut strong adhesives.

    • There is LCD screen connector on the left side, so be careful to slide guitar picks.

  5. Release LCD screen connector firstly. Remove LCD screen. Remove LCD screen.
    • Release LCD screen connector firstly.

    • Remove LCD screen.

  6. Undo 14 screws by T4 Torx screwdriver Pry up motherboard assembly. Battery flex connector is connected with motherboard, so be careful to pry the assembly up.
    • Undo 14 screws by T4 Torx screwdriver

    • Pry up motherboard assembly.

    • Battery flex connector is connected with motherboard, so be careful to pry the assembly up.

  7. Nintendo Switch 키트

    게임으로 돌아가기 위한 빠른 해결책

    Nintendo Switch 키트 쇼핑하기

    Nintendo Switch 키트

    게임으로 돌아가기 위한 빠른 해결책

    Nintendo Switch 키트 쇼핑하기
  8. Release battery flex connector. Separate motherboard assembly from back cover assembly.
    • Release battery flex connector.

    • Separate motherboard assembly from back cover assembly.

  9. Undo 3 screws here. Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it. Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it.
    • Undo 3 screws here.

    • Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it.

  10. Remove front-facing camera. Remove front-facing camera.
    • Remove front-facing camera.

  11. Remove rear camera. Remove rear camera. Remove rear camera.
    • Remove rear camera.

  12. Remove earpiece. Remove earpiece.
    • Remove earpiece.

  13. Remove loudspeaker. Remove loudspeaker.
    • Remove loudspeaker.

  14. Here is the motherboard. Here is the motherboard.
    • Here is the motherboard.

  15. Use spudger to cut adhesive and pry the battery up. Use spudger to cut adhesive and pry the battery up.
    • Use spudger to cut adhesive and pry the battery up.

  16. Take away headphone jack. Take away headphone jack. Take away headphone jack.
    • Take away headphone jack.

  17. Done
    • Done

결승점

다른 15명이 해당 안내서를 완성하였습니다.

Witrigs

회원 가입일: 2015년 11월 24일

64,656 평판

안내서 386개 작성하였습니다

Muito bom, parabéns!

Manoel - 답글

Could you guys tell me if the main speaker, at the bottom, has a special protection agains water spills, like a membrane or so, or is it pretty fine too spill water there?

setsuoleandro - 답글

Wi fi not trun on ..moto g3

Seoni Seoni - 답글

When you heat up the display, do you heat up the entire display or just around the edges? What heat gun/setting should i use? Can i use a blowdryer?

guest - 답글

Thanks. ......................

Biswajit Saha - 답글

댓글 쓰기

조회 통계:

24 시간 전: 5

7일 전: 30

30일 전: 164

전체 시간: 19,986