주요 콘텐츠로 건너뛰기

필요한 것

해당 분해도는 수리 안내서가 아닙니다. NBC Kentucky Derby Brooch 수리는 저희 서비스 설명서를 사용하십시오.

  1. NBC Kentucky Derby  Brooch Teardown, Assemble Horse: 1 단계, 이미지 1/3 NBC Kentucky Derby  Brooch Teardown, Assemble Horse: 1 단계, 이미지 2/3 NBC Kentucky Derby  Brooch Teardown, Assemble Horse: 1 단계, 이미지 3/3
    • Gather all components and flip everything over.

    • Mount the head, tail, and both legs by placing them over their pivot points.

  2. NBC Kentucky Derby  Brooch Teardown, Attach linkage: 2 단계, 이미지 1/3 NBC Kentucky Derby  Brooch Teardown, Attach linkage: 2 단계, 이미지 2/3 NBC Kentucky Derby  Brooch Teardown, Attach linkage: 2 단계, 이미지 3/3
    • Carefully align the linkage with the mounting holes on both legs.

    • Place two 3mm eyeglass screws into either end of the linkage.

    • Tighten the screws. These screws will self-tap into the legs. Be careful to not over-tighten and seize the linkage.

  3. NBC Kentucky Derby  Brooch Teardown, Mount servo: 3 단계, 이미지 1/3 NBC Kentucky Derby  Brooch Teardown, Mount servo: 3 단계, 이미지 2/3 NBC Kentucky Derby  Brooch Teardown, Mount servo: 3 단계, 이미지 3/3
    • Pull the servo through the donut hole of the PCB (top to bottom).

    • Orient the servo arm to the left (aligned with the rest of the body). This represents the zero degree location.

    • Manually move the servo arm down 90 degrees so it is now points downward into the work surface.

    • Mount the servo to the enclosure.

  4. NBC Kentucky Derby  Brooch Teardown, Assemble enclosure: 4 단계, 이미지 1/3 NBC Kentucky Derby  Brooch Teardown, Assemble enclosure: 4 단계, 이미지 2/3 NBC Kentucky Derby  Brooch Teardown, Assemble enclosure: 4 단계, 이미지 3/3
    • Place the PCB overtop the servo.

    • Route the servo's wire around various components as depicted.

    • Coil extra wire in available space.

  5. NBC Kentucky Derby  Brooch Teardown, Mount horse to enclosure: 5 단계, 이미지 1/3 NBC Kentucky Derby  Brooch Teardown, Mount horse to enclosure: 5 단계, 이미지 2/3 NBC Kentucky Derby  Brooch Teardown, Mount horse to enclosure: 5 단계, 이미지 3/3
    • Align the enclosure with the mounting holes on the backside of the horse's body.

    • Align servo arm with the drive gap in the linkage. Double check this correct before tightening.

    • Use two M2 screws to attach the horse to the enclosure.

  6. NBC Kentucky Derby  Brooch Teardown, Assemble back of enclosure: 6 단계, 이미지 1/3 NBC Kentucky Derby  Brooch Teardown, Assemble back of enclosure: 6 단계, 이미지 2/3 NBC Kentucky Derby  Brooch Teardown, Assemble back of enclosure: 6 단계, 이미지 3/3
    • Start by placing the bottom notched-side into the lip of the enclosure.

    • Align all three mounting holes from above.

    • Press firmly with both hands (avoid putting pressure on horse) and work your hands around the edges until the back is pressed flush.

    • Secure the back of the enclosure by driving three M2 screws into place. DO NOT OVER TIGHTEN!

  7. NBC Kentucky Derby  Brooch Teardown, Give it power: 7 단계, 이미지 1/2 NBC Kentucky Derby  Brooch Teardown, Give it power: 7 단계, 이미지 2/2
    • Attach wiring harness to brooch.

    • Plug wiring harness into USB power supply.

Justin Sinichko

회원 가입일: 2018년 05월 01일

165 평판

안내서 1개 작성함

0 Comments

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 5

30일 전: 16

전체 시간: 876