해당 분해도에 사용된 도구

소개

Here is the disassembly for a Nikon Coolpix 3200 digital camera.

해당 분해도는 수리 안내서가 아닙니다. Nikon Coolpix 3200 수리는 저희 서비스 설명서를 사용하십시오.

  1. Use a small Philips screwdriver to remove the screws from the base of the camera.
    • Use a small Philips screwdriver to remove the screws from the base of the camera.

    댓글 쓰기

  2. Use a small Philips screwdriver to remove the screws from the side of the camera where the computer lead is.
    • Use a small Philips screwdriver to remove the screws from the side of the camera where the computer lead is.

    댓글 쓰기

    • Use a small Philips screwdriver to remove the two screws from the side of the camera where the card reader is.

    댓글 쓰기

    • Pry apart the outer casing. A gray plastic threaded piece (used to attach camera to a tripod) will fall out.

    댓글 쓰기

    • Use a Phillips screwdriver to remove the two silver screws that connect the circuit board to the outer front casing.

    댓글 쓰기

    • Pry apart the front outer casing from the circuit board. The camera will now be in three pieces.

    댓글 쓰기

    • Pull the connecting strip on the circuit board which connects it to the back outer casing.

    댓글 쓰기

    • Use a Philips screwdriver to remove the two screws next to the computer port and the brass screw on the circuit board.

    댓글 쓰기

  3. Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    • Use a Phillips screwdriver to unscrew the three screws that connect the outer lens rim to the front casing.

    댓글 쓰기

    • Use a Philips screwdriver to remove the three screws that hold the flash cover to the outer front casing.

    댓글 쓰기

    • Open the lid of the battery compartment and use a Philips screwdriver to remove the two screws at the bottom.

    댓글 쓰기

    • Use a Phillips screwdriver to unscrew the two screws that connect the inside battery casing to the front of the outer casing.

    댓글 쓰기

    • Pull off the battery casing from the inside of the outer front casing. The circuit board, battery casing, and front outer casing will be attached by a connecting strip along with red and black wires.

    댓글 쓰기

    • Use scissors to cut the red and black wires away from the battery points of contact.

    댓글 쓰기

    • Pull the connecting strip away from the circuit board to separate it from the front casing.

    댓글 쓰기

    • Use a Philips screwdriver to unscrew the two screws that connect the photo button to the outer front casing.

    댓글 쓰기

    • Firmly press on the photo button and this component will pop out.

    댓글 쓰기

    • Use a scalpel to pry apart the metal inner part of the button from the plastic outer piece.

    댓글 쓰기

    • Use your fingernails to peel the outer rim from the front casing.

    댓글 쓰기

    • Pull the connecting strip out of the circuit board to separate it from the LCD screen.

    댓글 쓰기

    • Use your fingernails to pry apart the back metal piece of the screen (covered by a black plastic film) from the front section of the screen.

    댓글 쓰기

    • Pry apart the back black piece and front white piece of the screen. Inside the screen there are four sheets of plastic: one opaque, two mirrored, and one thicker plastic sheet which has a foil piece attached to it.

    댓글 쓰기

    • Use a hammer and chisel to separate the lens piece of the camera from the circuit board.

    댓글 쓰기

    • Use your fingernails to pry off the motor, motor cover, and flash piece from the lens piece of the camera.

    댓글 쓰기

Milly Whitehead

회원 가입일: 2010년 03월 09일

47 평판

안내서 1개 작성함

Oh, and then just do everything in reverse to put it back together again? That hammer and chisel bit bothers me a bit.

mrs_prolo - 답글

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 4

지난 30일: 13

전체 시간: 5,010