주요 콘텐츠로 건너뛰기

필요한 것

해당 분해도는 수리 안내서가 아닙니다. Nintendo GameCube 수리는 저희 서비스 설명서를 사용하십시오.

  1. Nintendo GameCube Teardown, Nintendo GameCube Teardown: 1 단계, 이미지 1/3 Nintendo GameCube Teardown, Nintendo GameCube Teardown: 1 단계, 이미지 2/3 Nintendo GameCube Teardown, Nintendo GameCube Teardown: 1 단계, 이미지 3/3
    • Flip the unit upside down and remove the screws sitting in the four deep holes in the corners using a 4.5mm gamebit driver. Don't remove the enclosure yet!

    • Turn the device right side up again, and now lift the top case off. It'll come up easily.

  2. Nintendo GameCube Teardown: 2 단계, 이미지 1/3 Nintendo GameCube Teardown: 2 단계, 이미지 2/3 Nintendo GameCube Teardown: 2 단계, 이미지 3/3
    • Unsnap the controller port cover and the rearmost I/O-cover by unsnapping the two snaps on the sides of each cover. Don't remove the controller panel yet.

    • Then remove the heatsinks of the memory card slots (necessary step).

  3. Nintendo GameCube Teardown: 3 단계, 이미지 1/3 Nintendo GameCube Teardown: 3 단계, 이미지 2/3 Nintendo GameCube Teardown: 3 단계, 이미지 3/3
    • Now start removing the 'normal' Phillips #2 screws.

    • Start by removing the fan assembly.

    • then unscrew the 12 visible screws on the edging of the now not so cube-shaped GameCube.

  4. Nintendo GameCube Teardown: 4 단계, 이미지 1/1
    이 단계에 사용된 도구:
    Heavy-Duty Spudger
    $4.99
    구매
    • Now you can lift the drive assembly up. You maybe have to loosen it a bit with a screwdriver or a heavy duty spudger.

    • The mainboard is now visible.

  5. Nintendo GameCube Teardown: 5 단계, 이미지 1/2 Nintendo GameCube Teardown: 5 단계, 이미지 2/2
    • Now remove the heatsink. Unscrew the six screws holding it.

    • Now use anything flat and durable to carefully lift up the heatsink by putting it under the aluminium and using it gently as a lever.

  6. Nintendo GameCube Teardown: 6 단계, 이미지 1/2 Nintendo GameCube Teardown: 6 단계, 이미지 2/2
    • If there are thermal pads remaining on the processors and/or ram chips, remove them with a plastic spudger.

    • Now disconnect the controller port panel connector by lifting and jiggling it carefully. It should come off easily.

  7. Nintendo GameCube Teardown: 7 단계, 이미지 1/2 Nintendo GameCube Teardown: 7 단계, 이미지 2/2
    • 24 MB MoSys 1T-SRAM

    • ATI 'Flipper' GPU, 162 MHz with 3 MB 1T-SRAM embedded within the die

    • IBM 'Gekko' CPU, 486 MHz (PowerPC 750CXe-based core)

    • Connectors (2nd pic):

    • 'Hi Speed Port'

    • 'Serial Port 1'

    • 'Serial Port 2'

  8. Nintendo GameCube Teardown: 8 단계, 이미지 1/3 Nintendo GameCube Teardown: 8 단계, 이미지 2/3 Nintendo GameCube Teardown: 8 단계, 이미지 3/3
    • If you lift the mainboard up, you'll see a metal plate, probably for EMI-protection. Remove the two screws holding it and you have access to the internal power supply.

Thomas J

회원 가입일: 01/24/10

415 평판

안내서 1개 작성함

댓글 13개

Great teardown Thomas!

Miroslav Djuric - 답글

Miroslav Djuric로 부터 인용:

Great teardown Thomas!

Thanks!

Thomas J - 답글

WOW! Great work, Nintendo stuff is hard to open!

Mc128k - 답글

Mc128k로 부터 인용:

WOW! Great work, Nintendo stuff is hard to open!

Thank you! Everything beyond Triwing requires creativity.

Thomas J - 답글

Will I need to reapply the thermal paste?

http://i.imgur.com/Q6antAn.jpg

Calvin Hall - 답글

댓글 쓰기

조회 통계:

24 시간 전: 53

7일 전: 307

30일 전: 1,373

전체 시간: 138,525