주요 콘텐츠로 건너뛰기

모델 M7572 / 400 또는 500 MHz G3 프로세서

45 질문 전체 보기

pismo not getting power when power cord is attached.

My pismo was working perfect one day and the next would not power on. If I attach the power, it does not show the battery receiving any power from it thus not turning on. I have tried other power adapters that are proven to be good power sources but with no luck. Any ideas on where the problem may be?

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

점수 1
댓글 달기

답변 4개

선택된 답변

I had a Pismo conk out on me after having been in storage for a while. In the end, I opened up the machine and replaced the little battery on the logic board and it started back up again. But there are folks online who are saying that you might not even have to replace that battery -- just remove it, restart the computer, then plug the battery back in to recharge it. Here's that thread with all the details: http://forums.macrumors.com/archive/inde...

Not sure if this is your problem, since it sounds like your machine hasn't been in storage. But it might be worth a try!

해당 답변은 도움이 되었습니까?

점수 1

댓글 2개:

I noticed same thing after my Pismo sat idle for a long time, it wouldn't boot at all. simply unplugging the little battery on the logic board allowed it to boot again.

Thanks for all the info. I have not had any luck with the pismo getting power but I will check the DC board, Thanks so much.

댓글 달기
가장 유용한 답변

It sounds like your DC-in board has failed. Unfortunately, iFixit is currently out of stock on this item, but here is the link to the page anyways. You can find the apple Part # and maybe search google to find another site that might have one.

[연계 제품이 누락 또는 비활성화 됨: IF106-003]

해당 답변은 도움이 되었습니까?

점수 2

댓글 1개:

Tyler - Would you take the step and purchase the DC Sound card or would you suggest getting it checked out first. How strongly do you feel that it is the problem? Thanks for your time - Gary

댓글 달기

I had a similar sounding problem with my Pismo, except that the power was intermittent - if I wiggled the power connector I could get it to work. I removed the DC board according to the ifixit repair guide and resoldered the connection between the board and the connector - everything was fine again. I think the years of plugging/unplugging the adapter stressed the connection on the board and/or there was a weak solder joint - it does seem to be a bit of a stress point as the plug fits very tightly.

can you get power at all if you gently wiggle the adapter connector when plugged in? if so try resoldering the connector. if not, then as mentioned above it's likely a bad DC board.

해당 답변은 도움이 되었습니까?

점수 0

댓글 2개:

I have attempted to wiggle it to see if I can get power but with no luck.

ok so if it's not intermittent then maybe good chance it's the DC board itself. since ifixit is out of stock, I know for sure there are other sites you can find on google selling this board and other ... PB parts ... I've seen the DC board listed elsewhere (but it's cheaper here on ifixit!) Not sure what else you can try short of replacing the board...

댓글 달기

Definitely works unplugging the pram battery!

Easy to try and don't cost anything!

Give it a try first :-)

해당 답변은 도움이 되었습니까?

점수 0
댓글 달기

귀하의 답변을 추가하세요

montanaman 님은 대단히 고마워 할 것입니다.
조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 3

전체 시간: 4,392