주요 콘텐츠로 건너뛰기

기기를 수리하세요

수리할 권리

상점

6s와 유사한 하드웨어 사양의 4-inch iPhone은 2016년 3월에 출시되었습니다. 16/64GB 저장 옵션 및 은색, 스페이스 그레이, 금색 또는 로즈 골드로 제공됩니다. 모델 A1662 및 A1723.

840 질문 전체 보기

New Battery Pack doesn't charge

Hello

I replace the Battery as described. I Icon show the Battery will be chardged but it sucks on 1%

Any Idea what went wrong?

Regards

Gérard

Update (06/25/2018)

Block Image

The part most right of the connector is missing

The spudger of ifixit isn't the correct tool. The fingernail is a better tool!

이 질문에 답하세요 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

점수 0

댓글:

Hello

The situations is more strange as thought. The iPhone was charged now for more as a night and it displayed it was only charged with 1%

I left the iPhone on my desk and took my old iPhone 4S for my work. At night when I came home the iPhone SE was still on 1% without be on the charging cable. So it looks like the battery isn't communicate with the phone. All Mails during the days are loaded. The iPhone SE is visible in the Network by the DHCP Server and in iTunes (Version 12.6.2.20) I can still make a backup of it ?!?

Could it be an issue with a bad Battery Back. The Original Battery has Part 616-00107 the new one has 616-00106!

Regards

Gérard

의견 추가하세요

답변 2개

tristar ic, it fails when you use cables that arent original or MFI certified.

해당 답변은 도움이 되었습니까?

점수 0

댓글:

Very strange! Before the Battery Swap this cable works fine. This cable is able to charge my iPad Air 2 normally!

I charging always on the Computer. I will search for the Original USB Charger and give it another try.

Normally my iPhone SE is in an Original Mophie Juice Pack Plus. Even with the Pack (green switch) or with the Charge Cable of the Pack it won't load more as 1% (the Juice Pack is blinking so this seems to charge)

I will try to buy a new Cable in the local Apple Store but I can't image this will solve the problem

in that case, look next to battery connecter. There is a few very small components (caps and filters). one is for battery gas gauge and can be easily knocked off during a battery replacement.

hello lukerockhill

I will make a picture. propably you are right. their should be 4 components I see only 3. They are soo small. I used the original ifixit manual and the spudger of the ifixit toolbox. (Step. 12). It should be better to use the fingernails for this purpuse :-(

Is there I way to fix it? Bridge it? What component is missing?

dont bridge it, a capacitor goes there so you would be shorting out the line if you just connected the two pads. in the picture i think i see the cap that fell off touching the other component to the left of where it was. try to remove it and see if it works. alot of times caps are there just to smooth out the power and will work still when one is removed. but the component it seems to be touching is a filter for battery gas gauge.

의견 추가하세요

Try to charge the battery with the phone off.

해당 답변은 도움이 되었습니까?

점수 0

댓글:

I tried this also without success!

의견 추가하세요

귀하의 답변을 추가하십시오

Gerard Dirks 가/이 대단히 고마워 할 것입니다.
조회 통계:

24 시간 전: 0

7일 전: 2

30일 전: 2

전체 시간: 94