N3DSXL — A-Button requires significant pressure to input.

Question

New Nintendo 3DS XL

The Nintendo 3DS XL 2015, marketed as the New Nintendo 3DS XL, was released October 11, 2014 in Japan and February 13, 2015 in North America.

372 질문 전체 보기

Theg_ @theg18747

평판: 11

2

게시일: 2023년 8월 16일

옵션

N3DSXL — A-Button requires significant pressure to input.

So, I’ve had my 3DS XL around for maybe five or six years, maybe more, maybe less. It’s never had any problems like this before, ever, but all of a sudden the A-button requires a lot more pressure to properly input anything, whereas the other three buttons work perfectly fine.

I’ve changed out the silicon bit between both the buttons and the motherboard, though that seemed to make things worse for a little bit, as that only led to the buttons feeling just a touch more clunky and unsurprisingly didn’t fix my issue. I’ve boiled it down to either I need to clean out the sticker between the motherboard and the buttons, or to replace the sticker entirely, which won’t be all too hard since they’re fifty cents at the very worst. As an FYI, I’ve done some heavy mashing on the A-button, which kind of came naturally and is obviously the source of the problem. I’d rather not try to have this happen once every few years until I decide I’m done with it entirely, though.

Any suggestions?

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

예 아니요

점수 0

댓글 달기

답변 1개

선택된 답변

Nick P @np_f1_2021

평판: 1.6k

14

7

1

게시일: 2023년 8월 16일

옵션

Good morning,

My guess is that as a result of excessive use & wear, the pad has worn down to the point it barely functions.

My suggestion is that you tear it down and confirm this as chances are you will have to replace the button pad assembly (the electronic side)

해당 답변은 도움이 되었습니까?

예 아니요

점수 1

댓글 5개:

The pad as in the sticker, the motherboard or the rubber part?

Theg_ 의 2023년 8월 16일

Sticker. Open it up and just check to see if the pads on the sticker are worn. if not, then turn to the rubber and check. Most likely one of the two has excessive wear

Nick P 의 2023년 8월 16일

The sticker, as far as I can tell, doesn’t seem all too worn out, but there’s a few black specks hanging out where the A-button is supposed to be. Is that a sign of wearing, or is it just some dust that managed to find its way in there?

Theg_ 의 2023년 8월 17일

Aha. Black specs. I'm going to have a guess and say small pieces of the sticker have started to come off. Weird that it requires significant pressure but still, i reckon that isn't factory. Clean it off and check

Nick P 의 2023년 8월 18일

Took a while to get the motherboard and the sticker out, but I got a replacement and the buttons work just like new. Thanks!

Theg_ 의 2023년 8월 26일

댓글 달기

The pad as in the sticker, the motherboard or the rubber part? — Theg_
Sticker. Open it up and just check to see if the pads on the sticker are worn. if not, then turn to the rubber and check. Most likely one of the two has excessive wear — Nick P
The sticker, as far as I can tell, doesn’t seem all too worn out, but there’s a few black specks hanging out where the A-button is supposed to be. Is that a sign of wearing, or is it just some dust that managed to find its way in there? — Theg_
Aha. Black specs. I'm going to have a guess and say small pieces of the sticker have started to come off. Weird that it requires significant pressure but still, i reckon that isn't factory. Clean it off and check — Nick P
Took a while to get the motherboard and the sticker out, but I got a replacement and the buttons work just like new. Thanks! — Theg_

New Nintendo 3DS XL

N3DSXL — A-Button requires significant pressure to input.

답변 1개

귀하의 답변을 추가하세요