기기를 수리하세요 커뮤니티 상점

Accessing Logicboard

소개

In this guide you will learn how to remove the SD card circuit board to access the logic board. To access the logic board, you will need to unsolder two leads. For soldering instructions, please refer to steps 1 through 6 of this soldering guide.

필요한 것

  1. Accessing Logicboard, Front and Back Cover: 1 단계, 이미지 1/2 Accessing Logicboard, Front and Back Cover: 1 단계, 이미지 2/2

    • Remove the following screws:

    • Two silver 3.15mm Phillips #00 screws on the right side of the camera

    • Two silver 2.08mm Phillips #00 screws on the left side of the camera

    편집

  2. Accessing Logicboard: 2 단계, 이미지 1/1

    • Remove the two indicated screws on the bottom of the camera:

    • The screw circled in red is a longer silver 3.15mm Phillips #00 screw

    • The screw circled in blue is a shorter silver 2.25mm Phillips #00 screw

    편집

  3. Accessing Logicboard: 3 단계, 이미지 1/2 Accessing Logicboard: 3 단계, 이미지 2/2

    • Carefully pull the back of casing away from the front.

    편집

  4. Accessing Logicboard: 4 단계, 이미지 1/3 Accessing Logicboard: 4 단계, 이미지 2/3 Accessing Logicboard: 4 단계, 이미지 3/3

    • After removing the back cover, several things must be removed.

    • Silver donut-shaped button will fall off. Place separately. Remove the plug covers on the right side of camera, labeled “PC/AV” and “DC IN 4.5V”.

    편집

  5. Accessing Logicboard: 5 단계, 이미지 1/2 Accessing Logicboard: 5 단계, 이미지 2/2

    • To remove the front cover, gently hold the inside structure of the camera and slowly pull the front cover off.

    편집

  7. Accessing Logicboard, Logicboard: 6 단계, 이미지 1/2 Accessing Logicboard, Logicboard: 6 단계, 이미지 2/2

    • On the front of the camera, in battery case, remove screws indicated:

    • Two black 2.05mm Phillips #00 screws

    편집

  8. Accessing Logicboard: 7 단계, 이미지 1/2 Accessing Logicboard: 7 단계, 이미지 2/2

    • Flip the camera over to the backside and remove screws indicated:

    • The screw circled in red is a longer black 3.00mm Phillips #00 screw

    • The screw circled in blue is a shorter black 2.00mm Phillips #00 screw

    편집

  9. Accessing Logicboard: 8 단계, 이미지 1/1

    • Pull the cover plate off for the two power cord jacks.

    편집

  10. Accessing Logicboard: 9 단계, 이미지 1/3 Accessing Logicboard: 9 단계, 이미지 2/3 Accessing Logicboard: 9 단계, 이미지 3/3

    • Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder.

    편집

  11. Accessing Logicboard: 10 단계, 이미지 1/1

    • Remove the orange tape on top of the SD cardholder.

    편집

  12. Accessing Logicboard: 11 단계, 이미지 1/1

    • Open the battery cover.

    편집

  13. Accessing Logicboard: 12 단계, 이미지 1/2 Accessing Logicboard: 12 단계, 이미지 2/2

    • Lift the indicated plastic piece off.

    편집

  14. Accessing Logicboard: 13 단계, 이미지 1/2 Accessing Logicboard: 13 단계, 이미지 2/2

    • Remove screws indicated:

    • Two black 4.80mm Phillips #00 screws

    편집

  15. Accessing Logicboard: 14 단계, 이미지 1/1

    • Unsolder points indicated.

    • Please refer to steps 1 through 6 of the Ifixit soldering guide to unsolder these leads.

    편집

  16. Accessing Logicboard: 15 단계, 이미지 1/3 Accessing Logicboard: 15 단계, 이미지 2/3 Accessing Logicboard: 15 단계, 이미지 3/3

    • Carefully lift up SD cardholder to reveal logicboard.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 5명과 함께

Nicole Wong

회원 가입일: 01/30/11

329 평판

안내서 3개 작성하였습니다

배지: 7

배지 +4개 더

팀

Cal Poly, Team 4-29, Regan Winter 2011 Cal Poly, Team 4-29, Regan Winter 2011 회원

CPSU-REGAN-W11S4G29

3 회원들

안내서 10개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 1,380